Anleitung Samsung, modell SP-L335
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
1 0 When the input signal is a PC Timing (D-Sub/HDMI) signal, / is not supported. • - - - <16 : 9> Position Using this function, you can adjust the screen position if it is not aligned. Using 3-5 MENU DESCRIPTION Digital NR If dotted lines appear in an image or the screen shakes, enabling Digital NR (Noise Reduction) can improve the quality of the picture. 0 When the input signal is a PC Timing (D-Sub/HDMI) signal, does not operate. Black Level If the black level is unsuitable for the input signal, the dark parts of an image may look unclear or dim. Using this function, you can select a black level that can improve the visibility of the dark parts. 1 0 The can only be set for the 480i and 576i RGB signals in the [AV], [S-Video], and AV Timing (D-Sub) modes. For [AV], [S-Video], and the 480i and 576i signals of AV Timing (D-Sub). • <0 IRE> : Sets the black level to <0 IRE>. • <7.5 IRE> : Sets the black level to <7.5 IRE>. For the RGB signal of mode. • : Used in a normal environment. • : Used when the dark parts of an image are too bright. Overscan Using this function, you can cut off the edge of a picture when unnecessary information or images appear on the edge of the picture. 0 Overscan is not supported in [AV] and [S-Video] modes. 0 Overscan is supported only when the input signal is an AV Timing (D-Sub) or AV Timing (HDMI) signal. 0 If is turned off, unnecessary extra parts at the edges of an image may be shown. In this case, turn on. Film Mode Using this function, you can set the display mode so that it is optimized for playing movies. • - 1 0 is only be supported for the [AV], [S-Video], 480i, and 576i of AV Timing (D-Sub) signals. PC For PC signals, the four PC functions eliminate or reduce noise that causes unstable screen quality such as screen shaking. If the noise is not removed using Fine Adjustment, adjust the frequency to the maximum and then perform Fine Adjustment again. 0 These functions are only enabled for the PC Timing (D-Sub/HDMI) input of the D-Sub terminal. 1 □ Refer to PC Timing (D-Sub/HDMI). • : Used to adjust the frequency and phase of PC screen automatically. • : Used to adjust the frequency when vertical lines appear on the PC screen. • : Used to fine tune the PC screen. • : Using this function, you can reset the PC menu settings to the factory default settings. Zoom You can magnify the screen to a size you want. • <1X>-<2X>-<4X>-<8X> □ This function is only enabled when the input signal is a PC Timing (D-Sub/HDMI) signal. 3-5 Using EÜ 3-5-3. Setup SetuD J- Install : Front-Floor ► w Lamp Mode : Eco ► Auto Keystone : Off ► 00 V-Keystone i—i ' Û Background -Lsac ► Test Pattern ► © Video Type AmICi V» 1 Caption Network ■On ► Reset ► ▼ Move E1 Enter 0 Exit MENU DESCRIPTION Install To tailor the picture to the installation location (In front of the screen and hanging from the ceiling, behind the screen and hanging from the ceiling, etc,). You can invert the projected images vertically / horizontally. • : Normal Image • : Horizontal/Vertical Reversed Image • : Horizontally Reversed Image • : Vertically Reversed Image Lamp Mode Using this function, you can set the image brightness by adjusting the amount of light generated by the lamp. • : This mode is optimized for screens smaller than 100 inches. This mode decreases the lamp brightness and power consumption in order to extend the lamp lifetime and reduce noise and power consumption. • :This mode is a general mode and works well in most situations. • : This mode maximizes the lamp brightness when the ambient illumination is bright. As the brightness of the lamp increases, the lamp lifetime can be reduced and noise and power consumption may increase. Auto Keystone If video scenes are distorted or tilted, you can compensate for this by setting the function to so that the function automatically starts. • - V-Keystone If video scenes are distorted or tilted, you can compensate for this using the vertical/horizontal Keystone function. 0 The sound output of your projector is temporarily stopped while the keystone is being changed. 0 does not compensate for distorition in the On Screen Display (OSD) menu. Background You can select a screen which appears when there is no signal from the external device connected with a projector. • - - Test Pattern A default test pattern built into the projector. You can use it as a reference picture to optimize the installation of the projector and to optimize images. • : You can check whether the picture is distorted or not. • : You can reference and display picture format sizes such as 1.33 : 1 or 1.78 : ...
Dieses Handbuch ist für folgende Modelle:
Projektoren - SP-L255 (3.48 mb)
Projektoren - SP-L305 (3.48 mb)
Projektoren - SP-L355 (3.48 mb)
)
