Stimmen - 3, Durchschnittliche Bewertung: 5 ( )

Hersteller: Optoma Technology Dateigröße: 215.85 kb Dateiname: 31818c4d-df56-4cb1-ad27-83afbbdb2e1c.pdf Unterrichtssprache:

In addition, make sure you are not at the limits of your projector’s zoom capability so that you have some range for image adjustments. The AKPro attachment plate is designed so that the projector and other attached components form an average center of mass (gravity) approximately located at the center of the ceiling mount pipe. Therefore, the ideal ceiling mount location will be shifted by the AKPro 2” (50mm) toward the left side of the screen from the ceiling mount location indicated by your projector’s instructions. If your projector ceiling mount is already installed and you do not wish to move it (or similarly move the screen in the opposite direction) due to a shift by the AKPro system, then you can make fine horizontal shift adjustments to your projector (if available) combined with turning the projector (only as necessary) during final setup to compensate for the shift. Some small amount of image distortion (horizontal keystoning) may result but in most cases this will not be noticeable since the image edges will typically be masked by the screen borders. WARNING! Use extreme caution and appropriate hardware when installing heavy objects to a ceiling. Periodically check all fasteners and connection hardware to be sure they are not coming loose. Improper installation may lead to an increased risk of your equipment becoming unstable and possibly injuring someone. Optoma BX-AL133B User Manual and Installation Guide, Version 1.0, copyright Nov, 2008, all rights reserved, Panamorph Inc. Page 3 HHACBBAACCBBHHACBBAACCBB 16AKPro Compatible Optoma Projector Models HD80, HD81, HD81-LV, HD803, HD930, HD980, HD7200, HD8000, HT1080, HD806, HC815, HT1200, TX1080, HD80-LV, HD8000-LV, HD806-ISF Holes A Screws M4x30 Spacers 5/8” (3) Notes Optoma BX-AL133B User Manual and Installation Guide, Version 1.0, copyright Nov, 2008, all rights reserved, Panamorph Inc. Page 4 HD82, HD808, HD8200 B M6x45 5/8” (4) HD86 C M4x30 5/8” (3) CONNECTING THE AKPro ATTACHMENT PLATE (Chief RPA mount and Phillips screwdrivers required) 1. Position the projector bottom-up. Consult the Attachment Plate Diagram for plate orientation, hole positions and required screws and spacers for your projector model. Insert and tighten each screw through an appropriate silver washer and lock washer, the designated holes in the Attachment Plate, then through any required spacers and finally into the projector ceiling mount holes. 2. Using the included gold hex key, install the six 7/8” socket head screws each through a 3/8” aluminum spacer and into the six threaded holes from the ceiling side of the attachment plate. Thread only enough to extend the screw to the bottom of the plate. 3. Insure that the RPA mount head is secure (see instructions included with the RPA mount) and oriented properly relative to the 7/8” socket head screw heads so that the mounted projector will face the screen. Use two people to lift and position the projection assembly so that th eads of each of the 7/8” socket head screws rest within the matching final location of the R mount head. At this point the silver 3/8” spacers should be between the Attachment Plate and the RPA mount head. The projection assembly may be lowered to allow the 7/8” screw heads to rest on the RPA mount. However, a first person should continue to guide the projection assembly while and a second person uses the gold assembly wrench to tighten the 7/8” screws. When tightening these screws, do so in a pattern of incrementally driving each screw a little more into the attachment plate so that at any time the projection assembly is resting on as many screw heads as possible until all are tightened. If the lens must be removed for any length of time it is recommended that a similar weight be suspended from the front of the attachment kit to balance the weight of the projector. This will minimize unusual stresses on the ceiling mount system. Optoma BX-AL133B User Manual and Installation Guide, Version 1.0, copyright Nov, 2008, all rights reserved, Panamorph Inc. Page 5 Optoma BX-AL133B User Manual and Installation Guide, Version 1.0, copyright Nov, 2008, all rights reserved, Panamorph Inc. Page 6 ALTERNATE ATTACHMENT PLATE METHOD (Phillips screwdrivers, pliers, scissors and appropriate ceiling hooks required) 1. Install the Plate Hook Assemblies in the two “H” holes of the Attachment Plate (see diagram) with the hook ends on the ceiling side as shown above. Use pliers to bend the closed hooks apart just enough to install a Chain End at a later time. 2. Position the projector bottom-up. Consult the Attachment Plate Diagram for plate orientation, hole positions and required screws and spacers for your projector model. Insert and tighten the required screws through the ceiling mount adapter (not included), then through the designated holes of the Attachment Plate, and then through any required spacers and finally into the projector ceiling mount ho...

Herunterladen

Geben Sie zwei Ziffern: