|
Anleitung Zusammenfassung
This remote control is used for source selection, control, adaptation and set up. Other functions of the remote control are : • switching between stand by and operational mode. • switching to "pause" (blanked picture, full power for immediate restarting) • direct access to all connected sources. 6.2 Terminology overview Overview The following table gives an overview of the different functionality of the keys. R59770021 CLM R10+ 11/10/2010 6.Get 6.Geingstarted 10 3 10 19 MENU EXIT ENTER PAUSE TEXT PHASE TINT COLOR BRIGHTN CONTR 9 0 7 8 5 6 3 4 1 2 LENS LENS ZOOM LENS SHIFT LENS FOCUS 1 22 2 3 4 5 6 7 8 9 10 11 12 13 14 17 15 16 19 20 18 .. SHARPN LENS SHIFT 21 1 2 3 4 5 6 7 8 9 0 MENU EXIT ENTER RGB STBY PAUSE TEXT PATTERN WIND OW PIP LENS RIGGIN GAUTO 17582192016617 Image 6-1 Local keypad & remote control Ind. Key name Description 1 Pattern key Direct access key to the internal pattern selection menu. 2 RGB Toggle key to enable and disable colors in the adjustment mode. Toggle between red, green, blue and full RGB. 3 MENU Access key to the menu structure and key to quickly quit the adjustment menus. 4 Address key (recessed key), to enter the address of the projector (between 0 and 9) in the remote control. Press the recessed address key with a pencil, followed by pressing one digit button between 0 and 9. 5 LENS Direct access key to the lens adjustment menus. Toggling this key will change the projected pattern. 6 PAUSE To stop projection for a short time, press ’PAUSE’. The image disappears but full power is retained for immediate restarting. Shutter is closed. 7 STBY Standby function switch off the lamp and lamp electronics. The lamp cooling fans remain active for about 5 minutes. The speed of the other fans is reduced. 8 Rigging Direct access key to layout selection. Rigging key + sequence number opens directly the desired layout. 9 Auto User programmable key to get different functions from auto image, auto contrast/brightness to auto align. This key can open an Auto image menu so that the user has access to these different functions. 10 11 12 13 Digit buttons Lens zoom/focus Lens shift Picture controls 48 Direct input selection or numeric entries Zoom and focus controls of the lens Shift control of the lens, to shift the lens up/down or left/right Use these buttons to obtain the desired picture level. R59770021 CLM R10+ 11/10/2010 6. Getting started Ind. Key name Description 14 PHASE Used to remove the horizontal instability of the image (usually for RGB source). It adjusts the phase of the pixel sampling clock relative to the incoming signal. 15 FREEZ To freeze the actual projected image. Freeze sign is displayed in the upper left corner (a short press on the key). When pressing for 5 sec, the projector goes into stand-by. The lamp cooling fans remain active for about 5 minutes. The speed of the other fans is reduced. 16 TEXT Toggle key to activate or deactivate on screen text boxes while adjusting a setting. When adjusting one of the image controls, e.g.during a meeting, the normally displayed bar scale can be deactivated by pressing ’TEXT’ key first. To re-display the bar scale on the screen, press ’TEXT’ key again. When TEXT is ’off’, no adjustment menu’s will be displayed on the screen when entering the adjustment mode. All menus and adjustments remain active on the local LCD panel. 17 ENTER Key to confirm an adjustment or selection in the adjustment mode. 18 Cursor keys To make menu selections when in the adjustment mode 19 EXIT Key to go one menu stage higher than the actual position when in the adjustment mode. 20 WINDOW Selection of the active window, also in PIP mode. 21 PIP Direct access key for picture in picture selection. 22 RC Operating indication Lights up when a button on the remote control is pressed. (This is a visual indicator to check the operation of the remote control) Table 6-1 6.3 Operating the projector Overview • Switching on • Errors, warnings and messages during start up • Switching to standby • Switching off All four lamps must be physically installed before operating the projector. 6.3.1 Switching on How to switch on. 1. Press the power switch to switch on the projector. (image 6-2) - When ’0’ is visible, the projector is switched off. - When ’1’ is visible, the projector is switched on. The projector starts up in standby. The menus are accessible via the local LCD panel. To display an image, the standby key must be pressed once. Image 6-2 Power switch R59770021 CLM R10+ 11/10/2010 49 6. Ge t 6.Geingstarted Starting image projection via the standby key. 1. Press Stand by key once on the local keypad or on the remote control. (image 6-3) The projector status LED lights up. The projector starts up on the last saved source. Some lamp and runtime warnings can be displayed when an image is displayed after a start up. MENU EXIT ENTER PAUSE TEXT PHASE TINT COLOR BRIGHTN CONTR 9 0 7 8 5 6 3 4 1 2 LENS LENS ZOOM LENS SHIFT LENS FOCUS .. SHARPN LENS SHIFT 1 2 3 4 5 6 7 8 9 0 MENU EXI...
Dieses Handbuch ist für folgende Modelle:Projektoren - CLM R10+ R9050100 (12.78 mb)
Projektoren - CLM R10+ R90501005 (12.78 mb)