Stimmen - 5, Durchschnittliche Bewertung: 4.4
(
)
)
|
Anleitung Zusammenfassung
We have highlighted the DVR (TiVo/Replay) buttons in blue for easy referencing on the keypad. 1 2 3 4 5 6 7 8 9 2 EN 3 The remote control is equipped with the most common functions for operating your devices. However if you miss certain functions, this remote control can 'learn' these functions from the original remote control. To fully benefit from the support that Philips offers, register your product at: 2 Getting started 3 Check whether the buttons that you need for operating your TV are working. For an overview of the buttons and their functions see chapter 3.1. • If the TV responds as it should to all of the button commands, the SRP5107 -c a is ready for use. t If the device does not respond at all or not to all £ of the button commands, follow the instructions in -¡5 chapter 2.3. $ 2.1 Inserting the batteries • Insert 2 AA type batteries, noting the + and - configuration in the battery compartment. ^ Note_ When replacing the batteries, all user settings will be retained in the remote control memory for an unlimited period of time. 2.2 Testing the universal remote control It is advised to test whether your device(s) already respond(s) to the SRP5107 before setting it up (see chapter 2.3). The example below instructs you how to do this for your TV You can repeat the same steps for other devices (DVR, DVD player/recorder, Cable/Satellite box, DTV VCR, HD and auxiliary equipment) which you want to operate using the SRP5107. Example: testing the universal remote control on your TV: 1 Switch ON your TV manually or use the original remote control for this. Tune to channel 1. 2 Press the 03 device selection button to select TV • The red Setup light ® blinks. If the Setup) light ® did not blink, che ck whether the batteries are properly inserted (see chapter 2.1). 2.3 Setting up the universal remote control The example below instructs you how to set up your universal remote control for your TV. You can repeat the same steps for other devices (DVR, DVD player/recorder Cable/Satellite box, DTV VCR, HD and auxiliary equipment) which you want to operate, using the universal remote control. The remote control can be set up to operate any 7 of the following devices: Device name Description TV Traditional TV, LCD/Plasma TV, flat panel TV and projection TV, TV part of TV/VCR, TV/ VCR/DVD and TV/DVD combos DVR Digital/Personal Video Recorder (DVR/PVR), TiVo, DVR part of DVR/SAT DVR/Cable and DVR/DVD combos DVD DVD player/recorder (DVDR/DVDRW), DVD/Hard Disk Drive combination (DVDR-HDD), Blu-Ray player High Definition DVD player (HD-DVD), DVD part of TV/DVD, TV/VCR/DVD, DVR/DVD and VCR/DVD combos CBL/SAT Cable box, satellite receiver Internet Protocol TV (IPTV), Free To Air TV High Definition Television decoder (HDTV), Digital Television (DTV), TiVo, SAT/Digital TV (DTV)/WebTV DTV/Advanced Television Systems (ATSC) - Digital To Analog Converter; CBL part of DVR/ Cable combos and SAT part of DVR/ SAT combos VCR Video cassette player/recorderVCR part of TV/VCR, TV/VCR/DVD and VCR/DVD combos 4 EN EN 5 AUX Auxiliary equipment CD, Audio System, Laser Disc, Digital Picture Frame, Media Center PC, Home Automation, Home Theater in a Box _(HTIB)_ HD Any of the above listed devices Example: setting up the universal remote control to operate your TV: 1 Switch ON the TV manually or use the original remote control for this. Tune to channel 1. 2 Press and hold the G3 device selection button for 5 seconds until the red Setup light ® blinks. | • The remote control is now in setup mode. 5 sec. 5 - 60 sec. 3 Look up the 4-digit code for your brand in the brand list at the back of this user manual. A 4-digit code is shown for each brand. Use the digit buttons to enter the code for your brand (e.g. Philips, CDCDCDCD)' • If the red Setup light @ turns off, an invalid code was entered. In this case, try again. 4 Aim the remote control at tine TV. Press and hold the QD button. Release it immediately as soon as the TV switches off • This step normally takes between 5 and 60 seconds. In extreme circumstances this step can take up to 15 minutes. 5 Switch ON the TV. Try out the buttons "that you need for operating it. Try, for example, if the - CH + and digit , buttons function prope rly • If a bu tton does not work as expected, press and hold that button. Release it immediately as soon as it works. For more information, see chapter 2.3.3. 6 Press the G3 device selection button twice to finish setup. • When no button is pressed for 5 minutes or more, the remote control will exit setup mo de, autom atically saving all your settings. n Important If you made a mistake: • Press the device selection button twice to exit setup. The red Setup light ® turns off. • Restart from the beginning. • If the device does not respond at all or not to all of the button commands or if you cannot find the code for your brand, enter r9, 9, 9, 9’ in step 3 and contin...