Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Please use the catalog in this manual to make sure that all parts have been included in your shipment. Use only Hoist replacement parts when servicing. Failure to do so will void your warranty and could result in personal injury. Hoist equipment is designed to provide the smoothest, most effective exercise motion possible. After assembly, you should check all functions to ensure correct operation. If you experience problems, first recheck the assembly instructions to locate any possible errors made during assembly. If you are unable to correct the problem, call your authorized Hoist dealer. Be sure to have your serial number and this catalog when calling. When all parts have been accounted for, continue on to Step 2. When ordering use the part number and description from the catalog. HF4985 ASSEMBLY Page -2 ASSEMBLY INSTRUCTIONS HF4985 ASSEMBLY Page -3 ASSEMBLY I N S T R U C T I O N S HF4985 ASSEMBLY Page - 4 F R A M E A S S E M B L Y Step 2 ASSEMBLY INSTRUCTIONS FRAME ASSEMBL Y Step 2a 1 -Right Support Beam 2 -Left Support Beam 4 -Base Support 10 -Gusset Plate Part Descriptions A -1/2-13 UNC x 4” Hex Bolt AA -1/2” Flat Washer BA -1/2” Nylok Nut Hardware Descriptions HF4985 ASSEMBLY Page -5 ASSEMBLY I N S T R U C T I O N S HF4985 ASSEMBLY Page - 6 10 BA AA BA 4 1 AA AA AA AA 10 AA A 4 2 AA AA AA AA AA BA A BA AA NOTE: Parts (1) and (2) are not the same. There are holes on the back side of the parts that are closer to one edge. That edge mounts to the inside of the unit (as shown in the diagram below). If mounted on the wrong side, the Safety Tier option will not work. ASSEMBLY INSTRUCTIONS FRAME ASSEMBL Y Step 2b 4 -Base Support 5 -Rear Support 6 -Rear Cross Member Part Descriptions B -1/2”-13UNC x 3 1/4” Hex Bolt AA -1/2” Flat Washer BA-1/2” Nylok Nut Hardware Descriptions HF4985 ASSEMBLY Page -7 ASSEMBLY I N S T R U C T I O N S HF4985 ASSEMBLY Page - 8 5 B AA 5 AA BA AA BA AA AA B 6 AA BA AA BA 4 4 ASSEMBLY INSTRUCTIONS FRAME ASSEMBL Y Step 2c 1 -Right Support Beam 2 -Left Support Beam 3 -Top Cross Member 5 -Rear Support 11 -Bar Rack Part Descriptions A --13UNC x 4” Hex Bolt C -1/2”-13UNC x 4 1/4” Hex Bolt AA -1/2” Flat Washer BA -1/2” Nylok Nut 1/2” Hardware Descriptions HF4985 ASSEMBLY Page -9 ASSEMBLY I N S T R U C T I O N S HF4985 ASSEMBLY Page - 10 AA AA A A 11 5 A AA AA C AA AA A AA BA AA AA C AA AA BA BA BA 3 BA AA AA AA 11 5 1 2 ASSEMBLY INSTRUCTIONS FRAME ASSEMBL Y Step 2d 4 -Base Support 8 -Olympic Weight Mount 9 -Olympic Weight Bar 11 -Bar Rack 12 -Linear Shaft 13 -Hook Sleeve 14 -Roller Hook Part Descriptions D -3/8-16UNC x 2 1/4” Hex Bolt AB -3/8” Flat Washer BB -3/8” Nylok Nut Hardware Descriptions In this step; first, slide (13) into (14) and secure to one side of (9), repeat for other side of (9) and ook (9) onto both (11)’s. Next, place a finger of light grease (lithium, super lube, ect) into the inside of the bearings on both (8)’s. Using your finger, press the grease into the ball-bearings and their tracks. Repeat until the ball-bearing tracks are full of grease. Slide (12) into (8), then (8) into (9) and let (12) rest on (4), it will be secured in a late step. Repeat process for other side of (9). Wrench Tighten bolts. H HF4985 ASSEMBLY Page -11 ASSEMBLY I N S T R U C T I O N S HF4985 ASSEMBLY Page - 12 9 8 12 8 AB D 12 AB 13 14 BB See detail A for assembly instructions. Detail A Scale 2:1 Place a finger of light grease (lithium, super lube, ect.) into the inside of the bearing using your finger, press the grease into the ball-bearing and their tracks. Repeat until the ball-bearing tracks are full of grease. Place a finger of light grease (lithium, super lube, ect.) into the inside of the bearing using your finger, press the grease into the ball-bearing and their tracks. Repeat until the ball-bearing tracks are full of grease. 11 11 4 4 ASSEMBLY INSTRUCTIONS FRAME ASSEMBL Y Step 2e 1 -Right Support Beam 2 -Left Support Beam 5 -Rear Support 7 -Guide Rod Support 12 -25mm Linear Shaft Part Descriptions A --13UNC x 4” Hex Bolt AA -1/2” Flat Washer BA -1/2” Nylok Nut 1/2” Hardware Descriptions Slide the top of (12) up into the hole on the bottom of (5). Next, slide the bottom of (12) into (7) and secure one (7) to (1), and the other (7) to (2). Wrench Tighten bolts. HF4985 ASSEMBLY Page -13 ASSEMBLY I N S T R U C T I O N S HF4985 ASSEMBLY Page - 14 BA AA A AA AA A 7 AA BA AA 7 AA 1 2 5 5 12 12 ASSEMBLY INSTRUCTIONS FRAME ASSEMBL Y Step 2f 5 -Rear Support 15 -Weight Holder 16 -Rubber Donut Part Descriptions E -3/8”-13UNC x 1” Hex Bolt AB -3/8” Flat Washer AC -3/8” Lock Washer Hardware Descriptions HF4985 ASSEMBLY Page -15 ASSEMBLY I N S T R U C T I O N S HF4985 ASSEMBLY Page - 16 15 16 15 AB 16 E AC AC E 5 5 AB Assemble the other 3 weight holders on this side as shown here. Assemble the other 3 weight holders on this side as shown here. ASSEMBLY INSTRUCTIONS PRE-ASSEMBL Y P AR TS Step 3a 5 -Rear Support 18 -2” x 3” End Cap Part Descriptions HF4985 ASSEMBLY Page -17 ASSEMBLY INSTRUCTIONS 5 5 ...