Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: INSTEON
Dateigröße: 46.37 kb
Dateiname: 73210qs.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
Recipients of the automated phone eall will hear a user recorded message identifying the concern. By linking an INSTEON motion sensor, door/window, and/or leak/flood sensor to the I/O Line, the phone dialer can eall you if any unauthorized movement, door/window activity or a leak takes place. Any device that transmits an INSTEON signal can be used to trigger the I/O Line - INsTeON Telephone Alert Kit to eall out simply by linking the devices together. Items you will Need Wire stripping tool * Set Button / Status LED I/O Line (screwdriver included) Screw Terminals I/O Linc’s Screw Terminals "\ 5V GND Sense N/C N/O Common 5 Volts Ground Sensor Input Normally Closed Normally Open Switches between N/O and N/C Using an INSTEON Device to Trigger a Telephone Alert 1) Follow Phone Dialer’s User’s Instructions on Installation and Programming (disregard instructions referring to other Skylink products) 2) Plug your I/O Line into an un-switehed outlet near your Phone Dialer I/O Line’s Status LED will turn on 3) Remove the pre-stripped plastic insulation from included connection wire 4) Insert one of connection wire’s stripped leads into I/O Line’s N/C terminal (see Figure 1) 5) Insert connection wire’s other stripped lead into I/O Line’s Common terminal (see Figure 1) 6) Open Phone Dialer’s cover and insert connection wire into Phone Dialer’s N.C. terminals (remove existing metal jumper). Close Phone Dialer’s cover. Link INSTEON Controller/Sensor to I/O Linc 7) Press & hold the Set button on the INSTEON device you want to trigger a telephone alert Controller’s Status LED will begin blinking 8) Press & hold I/O Line’s Set button until it beeps (about 3 seconds) I/O Line will beep onee again to confirm linking; Controller’s LED will stop blinking Set I/O Linc into Momentary Mode 9) Press & hold I/O Line’s Set button until it beeps (about 3 seconds) 10) Press & hold I/O Line’s Set button until it beeps (about 3 seconds) 11) Press & hold I/O Line’s Set button until it beeps (about 3 seconds) I/O Line’ Status LED will stop blinking 12) Press & hold I/O Line’s Set button until it beeps (about 3 seconds) 13) Press & hold I/O Line’s Set button until it beeps (about 3 seconds) 14) Press & hold I/O Line’s Set button until it beeps (about 3 seconds) I/O Line’ Status LED will stop blinking 15) Test by turning your INSTEON Controller/Sensor On or Off Phone Dialer will eall according to its programming in step 1 in response to INSTEON On and Off commands Wiring I/O Linc to Phone Dialer fh if ü Figure 1 Connection Wire Questions? Click: For Advanced Features and X10 compatibility, refer to I/O Line’s Owner’s Manual: Line - INSTEON Low Voltage / Contact Closure Interface Owner%27s Manual Call: Friendly tech support @ 1-8OO-SMARTHOME (800-762-7846) J Page 1 of 1 Rev. 04-06-2009 SmartLabs Limited Warranty - SmartLabs warrants to original consumer of this product for a period of 2 years from date of purchase, this product will be free from defects in material & workmanship & will perform in substantial conformity with its owner's manual. Warranty shall not apply to defects caused by misuse or neglect. U.S. Patent No. 7,345,998, International patents pending ©Copyright 2009 SmartLabs, 16542 Millikan Ave., Irvine, CA 92606, 1-800-SMARTHQME (800-762-7846) smart...