Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
82258 Genie Z-80/60 27 First Edition · Fifth Printing Operator's Manual DECALS 33952 32700 65269 28236 28176 30080 28163 or 44986 82296 28174 or 28235 28175 28164 28171 Serial Plate 28160 27564 28161 82202 or 82203 or 82204 82296 133400 133400 43595 43595 28165 82281 28174 or 28235 52966 or 52967 82312 27205 27204 82269 28161 82296 43595 31060 27206 27206 65278 65278 65278 65278 27207 27207 40434 28177 40434 28181 28177 82366 32700 65269 27564 31060 28161 28158 or 28159 82268 72169 72168 82403 133400 82296 43595 133400 38149 28 Genie Z-80/60 Part No. 82258 Operator's Manual First Edition · Fifth Printing Transport and Lifting Instructions Observe and Obey: The transport vehicle must be parked on a level surface. The transport vehicle must be secured to prevent rolling while the machine is being loaded. Be sure the vehicle capacity, loading surfaces and chains or straps are sufficient to withstand the machine weight. See the serial plate for the machine weight. Be sure the turntable is secured with the turntable rotation lock before transporting. Be sure to unlock the turntable for operation. Free-wheel Configuration for Winching Chock the wheels to prevent the machine from rolling. 2WD models: Release the non-steer wheel brakes by turning over the drive hub disconnect caps. 4WD models: Release the wheel brakes by turning over all four drive hub disconnect caps. Be sure the winch line is properly secured to the drive chassis tie points and the path is clear of all obstructions. Reverse the procedures described to re-engage the brakes. Note: The pump free-wheel valve should always remain closed. Disengage Engage Part No. 82258 Genie Z-80/60 29 First Edition · Fifth Printing Operator's Manual Securing to Truck or Trailer for Transit Always use the turntable rotation lock pin each time the machine is transported. Turn the key switch to the off position and remove the key before transporting. Inspect the entire machine for loose or unsecured items. Securing the Chassis Use chains of ample load capacity. Use a minimum of 5 chains. Adjust the rigging to prevent damage to the chains. Securing the Platform Place a block under the rotator. Do not allow the block to contact the platform cylinder. Secure the platform with a nylon strap placed over the jib knuckle. Do not use excessive downward force when securing the boom section. TRANSPORT AND LIFTING INSTRUCTIONS Truck bed 30 Genie Z-80/60 Part No. 82258 Operator's Manual First Edition · Fifth Printing TRANSPORT AND LIFTING INSTRUCTIONS Observe and Obey: Only qualified riggers should rig and lift the machine. Be sure the crane capacity, loading surfaces and straps or lines are sufficient to withstand the machine weight. See the serial plate for the machine weight. Lifting Instructions Fully lower and retract both the primary and secondary booms. Remove all loose items on the machine. Rotate the turntable 90 degrees. Determine the center of gravity of your machine using the measurements on the pictures on this page. Attach the rigging only to the designated lifting points on the machine. Attach the rigging to the 2 chassis lifting points farthest from the turntable lifting point. Adjust the rigging to prevent damage to the machine and to keep the machine level. Chassis Lifting Points (2) Turntable Lifting Point 39.61 in / 1 m 34.18 in 86.8 cm 56 in 1.42 m Part No. 82258 Genie Z-80/60 31 First Edition · Fifth Printing Operator's Manual Specifications Z-80/60 Height, working maximum 86 ft 26.2 m Height, platform maximum 80 ft 24.4 m Height, stowed maximum 9 ft 10 in 3 m Horizontal reach maximum 60 ft 18.3 m Width 8 ft 2 in 2.5 m Length, stowed 37 ft 11.3 m Length, stowed for transport 30 ft 9.1 m Maximum load capacity 500 lb 227 kg Wheelbase 9 ft 4 in 2.8 m Ground clearance 12 in 30.5 cm Turning radius, outside 2 wheel steer 24 ft 7 in 7.5 m 4 wheel steer 15 ft 2 in 4.6 m Turning radius, inside 2 wheel steer 14 ft 6 in 4.4 m 4 wheel steer 7 ft 2.1 m Turntable rotation (degrees) 360° continuous Turntable tailswing, secondary boom lowered 10 ft 10 in 3.3 m Turntable tailswing, secondary boom raised 3 ft 90 cm Power source Perkins Diesel 704-30 (choice) Deutz Diesel F4L913 GM 3.0L Drive speed, stowed 3 mph 4.8 km/h 40 ft/9.1 sec 12.2 m/9.1 sec Drive speed, 0.7 mph 1.1 km/h raised or extended 40 ft/40 sec 12.2 m/40 sec Continuous improvement of our products is a Genie policy. Product specifications are subject to change without notice or obligation. Controls 12V DC proportional Platform dimensions, 6 foot 72 in x 30 in (length x width) 1.8 m x 76 cm Platform dimensions, 8 foot 96 in x 36 in (length x width) 2.4 m x 91 cm Platform leveling self-leveling Platform rotation 160° AC outlet in platform standard Hydraulic pressure (maximum) 3200 psi (boom functions) 220 bar Tire size 18-625, 16 ply FF Gradeability, 4WD, stowed 50 % Gradeability, 2WD, stowed 30 % Fuel tank capacity 40 gallons 151 liters Weight See Serial Plate (Machine weights vary with option configurations) Airbo...