Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
If Base Station battery (optional) is low, it will beep every few minutes. Replace with 9-Volt battery (not provided). For peak performance inspect batteries annually and replace as needed. Base Station Switches: Switch #1: Switch #2: Programming Additional PIR Motion Sensors: The Base Station can learn the code of up to 3 additional PIR Motion Sensors, responding with unique buzzes. To program additional PIR Motion Sensors see Step 6. To order additional PIR Motion Sensors call 1-800-528-9131. Clear Memory: Press and hold the Learn Button on the Base Station until 3 beeps are heard. On/Off: To turn Base Station off hold down the Mute Button until it powers down. The Base Station can be turned on by pressing the Mute Button. Mute: Press and release the Mute Button to put the Base Station into Sleep Mode for one hour. After an hour it will activate automatically. 1 2 ON OFF OFF Buzzer Off ON Buzzer On (Default) OFF Long Buzz ON Short Buzz (Default) To prevent possible SERIOUS INJURY or DEATH from electrocution, outputs are suitable ONLY for controlling low voltage devices, 24V max, ac or dc. 1 2 Test PIR Motion Sensor by waving hand in front of sensor. Test light should flash. Secure cover with the smallest screws. Insert battery pack facing away from circuit board and attach cover. NOTE: Ensure the batteries do not touch the circuit board and the antenna and battery wires are not pinched. Antenna PIR Sensor Switch #1:. Switch #2: ON OFF 1 2 Step 4 Switch Settings Switch #1 Test Switch #2 Button OFF Low Sensitivity ON High Sensitivity (Default) OFF 15' Detection Range ON 30' Detection Range (Default) NOTE: To avoid unwanted detection of small animals move Switch #2 to OFF. Step 3 PIR Motion Sensor Assembly & Test Attach PIR Motion Sensor box to mounting plate with large silver screw. Tighten screw until PIR Motion Sensor stays in place when repositioned. Install 4 AA Alkaline batteries (not provided). (Lithium batteries recommended for colder environments.) Test light will flash. Step 1 Step 2 3 Mount PIR Motion Sensor horizontally on solid surface a few feet off the ground and within 900' of Base Station (rotate sensor to access screw holes). Unit should be able to swivel as needed. Attach sun/rain shield. NOTE: Keep PIR Motion Sensor antenna away from metal objects. Do not mount PIR Motion Sensor in direct sunlight, near moving tree branches, or in the path of a sprinkler system. PIR Motion Sensor Installation 3' - 5' 10' - 20' - - ACCESSORY N/O (Normally Open) COM (Common) The Base Station has a relay which can activate other devices such as a low voltage doorbell, buzzer or light. The accessory device will need a separate power supply. The accessories can be purchased at any electronics store. NOTE: Output switching capacity is low voltage (max 24V dc or ac). Advanced Features Vehicle Alert Installation: For cars, the best mounting position is about 4' high, between 10-20' back, and angled to see the back of car after passing the sensor. Step 7 Step 5 Plug in Base Station. Adhere rubber pads to bottom. A 9-Volt battery (not provided) is optional in case of power failures. OPTIONAL A B Programming PIR Motion Sensor to Base Station B Within 5 seconds, wave hand in front of PIR Motion Sensor. Test light will illuminate and Base Station will buzz. A B A Ensure Base Station and PIR Motion Sensor are in close proximity to each other. Press and release learn button on Base Station. Buzzer will sound. Step 6 The PIR Motion Sensor lights up, but the Base Station does not respond. The PIR Motion Sensor must be programmed to Base Station (See Step 6). Ensure Base Station is on and is not muted. If the green power light is not lit or is flashing, press the Mute Button on the top of the Base Station to wake it up. If the green power is illuminated, look at the two small white Base Station switches next to the Learn Button. The #1 Dip Switch should be down, towards the circuit board. If it is up, the Base Station has been muted. If the Base Station signals when you press the Learn Button, it is not muted. The Alert is not getting expected transmission range. Keep both antennas vertical and keep PIR Motion Sensor antenna away from trees and metal objects. Ensure Base Station is in clearest possible sight of the PIR Motion Sensor. The less objects between the devices, the longer the range. PIR Motion Sensor is detecting motion only part of the time. To detect cars, it is best to mount PIR Motion Sensor at height of car’s motor and have it between ten and twenty feet from the road. Swivel sensor as needed. Troubleshooting The Alert is giving false alarms. Check for moving tree branches or insects in sensor window. PIR sensor can also be triggered by light shining directly in sensor window, such as reflected sunlight, or motion in front of a light source. It is possible that condensation has built up on the sensor. Wipe condensation from PIR Motion Sensor with cotton swab. Let it sit inside for a few hours, open to the ai...