Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
13204 Phone 1-800-732-4065 315-476-5151 Fax 315-476-5044 Owner’s Manual Thank You for Choosing an Oneida Air Systems Product! OAS manufactures and sells dust collection equipment only. Our qualified technicians and sales staff are available 7:30am -6:00pm EST Mon. -Thur. and 7:30am -5:00pm EST Fri. to answer any questions concerning OAS products and dust collection. Call for ductwork design and ductwork quotes, including system pricing and shipping cost. Read the entire Owner’s Manual before installing or operating system! Proudly Made in the U.S.A. Table of Contents Page I. System Start-Up Information 2 II. Direct Drive Configurations 3 III. General Specifications & Fan Performance Curve 4 IV. Dimensions 5 V. Stand Assembly 6 VI. General Assembly Instructions 7 -8 VII. Fan / Blower Maintenance 8 VIII. External Filter Box Assembly 9 IX. Filter Maintenance 10 X. Wire Diagram 11 XI. Accessories 12 XII. Troubleshooting 13 XIII. Fire Hazards -Read Before Installing System 14 XIV. Terms and Conditions 15 1 5 -7.5 HP Direct Drive Owner’s Manual c O.A.S. 2002 I. System Start-Up Information 1. Read the installation and maintenance instructions as well as the recommended safety practices in this manual. 2. Install Ductwork completely: A.) Seal ductwork with silicone sealant or duct tape. B.) Have Dust Bin in place and sealed before running Dust Collector. 3. Wire Fan / Blower according to wire diagram on pg. 11 in this owner’s manual. 4. Have a licensed electrician check current draw on motor with all gates open. Current draw should not exceed maximum motor amperage. (OAS is not responsible fordestroyed motors.) Caution The Direct Drive Fan / Blower makes the system top heavy! Use extreme care when setting the unit up! WarningCheck amperage draw during operation with all blast gates open. Make certain amperage is not outside operating limit indicated on motor plate! Warning If amperage is too high -shut down immediately! (See troubleshooting section.) Warning Do not operate Fan / Blower unless Cyclone and Dust Bin are in place. Motor will over heat! 2 5 -7.5 HP Direct Drive Owner’s Manual c O.A.S. 2002 II. 5 & 7.5hp Direct Drive Configurations 1. No Filter - Vent Outside - Caution: 1. No Filter If exhaust air is vented outside you must provide make up / return air. Flue gases (carbon monoxide) can be drawn into the shop fromfurnaces, water heaters or other appliances. 2. External Cartridge Filters 3. External Tube Filter 5 - 7.5 HP Direct Drive Owner’s Manual c O.A.S. 2002 Plenum Assembly Tube Filters 5 Gal. Buckets - Collects fine dust Plenum Assembly Removable Dust Containers Removable Chip / Dust Bin Pleated Cartridge Filters 3 III. General Specifications & Fan Performance Curves Physical and Electrical Data for 5 and 7.5hp Direct Drive Systems. System Performance 5hp 1220 max cfm -2250 cfm w/ typical ductwork 7.5hp 2900 max cfm -2500 cfm w/ typical ductwork System Dimensions Height w/ 55 Gal. Drum: 132” Footprint: 8.5’ x 3’ Fan Wheel diameter: 16” Air Foil design Cyclone Inlet: 10” Integral Fan Blower -5hp TEFC 60 Hz Motor -Single Phase Insulation Class: F4 Voltage: 230 Amperage: 19.8 Made in U.S.A. Integral Fan Blower -7.5hp TEFC 60 Hz Motor -Three Phase Insulation Class: F4 Voltage: 208 -230 / 460 Amperage: 19.6 -18.4 / 9.2 Made in U.S.A. Tube Filter Bags Standard: 8 Tube Filters -5hp, 10 Tube Filters -7.5hp Needle felted polyester filter media BIA ZHI / 487 test Rated G Captures 99% of test material over 20 microns Dust Bin 55 Gal. Steel Drums Large dust bins available Options Angle iron stand for free-standing unit Silencers available Magnetic Motor Starters 5hp Fan Performance Curve 5hp System -2000 CFM @ 8” Static Pressure CFM 3000 2500 2000 1500 1000 500 0 3500 4000 3350 2875 2400 2025 1725 1400 1100 760 02 4 6 810 12 14 16 18 Static Pressure (In-H2O) -Fan Curve 7.5hp Fan Performance Curve 7.5hp System -2700 CFM @ 8” Static Pressure Captures 99.5% of test material between 0.2 -2.0 microns @ 11 fpm face velocity External Cartridge Filters (2) 2 Pleated Cartridges -260 sq. ft. Spun Bonded polyester BIA ZH1 / 487 test -Rated C Captures 99.99% of test material over 20 microns Captures99.9%oftestmaterialbetween0.2 -2.0microns @ 11fpm 02 4 6 8 10 12 14 16 18 Static Pressure (In-H2O) -Fan Curve 4 CFM 3000 2500 2000 1500 1000 500 0 3500 4000 3500 3100 2725 2440 2100 1875 1590 5 -7.5 HP Direct Drive Owner’s Manual c O.A.S. 2002 IV. Dimensions 14 1/2” 122 1/8” -with 8’ Bags 1.5” 1.25” Flange 7 3/4” 30” 39 1/4” 62” 73 1/8” 12” 12” 32 1/8” O.D. of Mounting Ring 69.875” 24 1/4” Bolt Holes 30 3/8” 10.031” I.D. 7.64” I.D. 131” w/ 55 gal. steel drum 105” Note: Overall height dimensions are w/ 55 gal. drum. 122.125” w/ 55 gal. steel drum 1.5” 102” 36” Top View 116 1/8” 43” Tube Filters -Height for 8’ bags. Other heights available. 5 5 -7.5 HP Direct Drive Owner’s Manual c O.A.S. 2002 V. Angle Iron Stand Cross Brace for Cyclone Angle Ring to sit on 1. Choose the system orientation, plenum can be on the r...