Stimmen - 0, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
LAM belongs to Class I laser products in accordance with IEC 60825-1. Here are some common precautions that must be observed. • ALWAYS turn the device off when it is not in use and when you change the battery! • NEVER look into the beam • NEVER subject LAM to excessive impacts • NEVER transport LAM without the case • NEVER disassemble LAM • NEVER reverse polarity of the battery • ALWAYS make sure that the device is fixed firmly on the weapon • ALWAYS remove battery when not in use for a long period • ALWAYS store in a warm dry place when not in use • ALWAYS clean output windows with soft cloth only • ALWAYS check the O-ring when replacing the battery. CONTENTS 1. Brief description ................................................. 2 2. Device design ..................................................... 3 3. DELIVERY SET ................................................ 8 3.1. Standard delivery set...................................... 8 3.2. Optional parts................................................. 8 4. Specifications...................................................... 9 5. OPERATION INSTRUCTIONS...................... 10 5.1. Installing the battery .................................... 10 5.2. Mounting LAM on a weapon....................... 10 5.3. Connecting the remote control..................... 11 5.4. Adjusting LAM on a weapon....................... 11 6. Maintenance, storage and transportation .......... 13 6.1. General......................................................... 13 6.2. Storage ......................................................... 14 6.3. Transportation.............................................. 15 7. TROUBLESHOOTING ................................... 17 8. WARRANTY ................................................... 18 9. CUSTOMER SUPPORT.................................. 19 10. QUALITY CERTIFICATE .............................. 20 1 Carefully read all the instructions prior to use. Failure to obey the instructions will void the warranty! INVISIBLE LASER RADIATION CLASS I LASER PRODUCT 830–860 nm 0,1mW. 1. Brief description LAM 10M IR laser aimer (hereinafter referred as LAM) is designed for precise aiming at night time. LAM forms an IR laser radiation spot on the target visible only through the night vision goggles. It can be attached to a weapon equipped with Picatinny rail MIL-STD-1913. Laser beam, created by a semiconductor laser diode, is invisible by naked eye, while it is perfectly visible through night vision goggles, rifle sights or hand-held devices. LAM meets the Class 1 eye safety requirements. Nevertheless users are not advised to look into the laser beam. 2 2. Device design 17 16 14 8765432 1 3 9 10 14 13 11 12 Fig. 1. LAM 10M IR 1 – clamp 2 – bracket 3 – stopper 4 – remote connector 5 – body 6 – emitter 7 – emitter cap 8 – emitter protective cap 9 – windage adjustment 10 – fastener 11 – ‘laser on’ warning 12 – elevation adjustment indicator 13 – fixation screw cap 14 – fixation screw 15 – battery compartment 16 – battery compartment cap 17 – operating modes switch 4 LAM consists of an emitter (6,7, Fig.1), a battery compartment (15,16, Fig.1), windage (9, Fig.1) and elevation (12, Fig.1) adjustment mechanisms, an operating modes switch (17, Fig.1), a remote switch (Fig.2), a clamp (1, Fig.1). A battery is to be inserted into the battery compartment (16, Fig.1). Battery compartment cap (15, Fig.1) is attached to the body with a rubber band. The battery compartment is sealed with rubber O-ring. A spare O-Ring is included in the delivery set. Emitter tube output window is closed with a cap (7, Fig.1) with an output aperture. When not in operation, the aperture is closed with a protective rubber cap (8, Fig.1). LAM is activated by means of the operating modes switch (17, Fig.1) and/or the remote switch (Fig.2). At switching laser radiation on ‘laser on’ warning indicator 11 lights. The switch (17, Fig.1) has the following positions: Mode OFF Off C The aimer is on; Continuous live fire R The aimer is on; Remote activation; live fire 5 LAM automatically turns off after 30 minutes of being switched in positions C and R. In order to activate LAM after it has automatically turned off, return the switch (17, Fig.1) into OFF position and then switch it to the desired position again. The remote switch (Fig.2) can be attached to LAM by a connector (3, Fig.2) with a union nut. When not in operation the connector (4, Fig. 1) is covered with a cap. The remote switch key (1, Fig.2) is attached to weapon pivot or grip with velcro tape (2, Fig.3). LAM is mounted on the Picatinny rail. An optional mount enables mounting LAM on a weapon barrel. This mount’s fitting diameter is 15 mm. 6 1 23 1 — key; 2 — velcro tape; 3 — connector Fig. 2. Remote switch 7 3. DELIVERY SET 3.1. Standard delivery set LAM is supplied in the following assembly: Quantity, pcs LAM 10M IR 1 Remote switch 1 Velcro tape 2 O-Ring 1 Case 1 Manual 1 Battery CR123 1 3.2. Optional parts LAM can be supplied with a...