Stimmen - 5, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
In case of eye contact, flush with flowing water. If swallowed, get medical help. Material Safety Data Sheet (MSDS) available from 1-800-544-6986. The label on your tool may include the following symbols: V ..........................volts mW......................milliwatts nm ........................wavelength in nanometers IIa ........................Class IIa Laser Installing the Batteries Ensure laser on/off switch (D) is in the full off position by moving switch actuator to "O" position. Remove the battery compartment cover (E). Insert 2 fresh 1.5 volt AA alkaline or heavy duty batteries making sure to match (+) and (-) terminals correctly. Replace battery compartment cover. WARNING: Batteries can explode, or leak, and can cause injury or fire. To reduce this risk: • Carefully follow all instructions and warnings on the battery label and package. • Always insert battery correctly with regard to polarity (+ and -), marked on the battery and the equipment. • Do not short battery terminals. • Do not charge battery. • Remove dead battery immediately and dispose of per local codes. • Do not dispose of battery in fire. • Keep batteries out of reach of children. • Remove battery if the device will not be used for several months. “Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductive materials such as keys, coins, hand tools and the like. The US Department of Transportation Hazardous Material Regulations (HMR) actually prohibit transporting batteries in commerce or on airplanes (i.e. packed in suitcases and carryon luggage) UNLESS they are properly protected from short circuits. So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit.” Operating Instructions Drywall Pin CAUTION: Pin is sharp and should be handled with care. NOTE: The drywall pin (A) can only be used for drywall, NOT other surfaces including plaster. • To press pin into drywall, first expose pin by rotating pin base from opposite side. • While maintaining pressure on pin base, insert pin straight and seat firmly against drywall surface as shown in Figure 1. The drywall pin should always be pushed in by hand and never driven by a hammer. • To remove drywall pin from the wall, pull out straight. CAUTION: Always be sure drywall pin is closed when not in use. Avoid exposure-Laser radiation emitted from this aperture. COMPLIES WITH 21CFR PARTS 1040.10 AND 1040.11 EXCEPT FOR DEVIATIONS PURSUANT TO LASER NOTICE NO.50, DATED JULY 26,2001. LISTED 406A WARNING/ADVERTENCIA AVERTISSEMENT BDL220S Type 1 3V DC To reduce the risk of injury, user must read and understand instruction manual. Para reducir el riesgo delesiones, el usuario debe leer y entender el manual de instrucciones. A titre preventif, lire le guide. Questions?: 1-800-54-HOW-TO Made in China Black & Decker (U.S.) Inc., Towson, MD 21286 U.S.A. CAUTION - CLASS 2 LASER RADIATION WHEN OPEN, DO NOT STARE INTO THE BEAM. PRECAUCION - RADIACION LASER DE CLASE 2 - CUANDO ABRA, NO FIJE SU SU VISTA EN EL RAYO. 3 C D E F Eviter toute exposition au rayonnement laser emis par cette ouverture. For your convenience and safety, the following labels are on your laser. Pour plus de commodite et de securite, les etiquettes suivantes sont apposees sur votre laser. Para su comodidad y seguridad, el laser incluye las siguientes etiquetas: Evite la exposicion - Por este orificio se emite la radiacion laser. I Thank you for choosing Black & Decker! Go to to register your new product. PLEASE READ BEFORE RETURNING THIS PRODUCT FOR ANY REASON: If you have a question or experience a problem with your Black & Decker purchase, go to HTTP://WWW.BLACKANDDECKER.COM/INSTANTANSWERS If you can’t find the answer or do not have access to the internet, call 1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. -- Fri. to speak with an agent. Please have the catalog number available when you call. for instant answers 24 hours a day. SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE. HORIZONTAL OR VERTICAL LINE PROJECTION ON A WALL 1). Hands free operation of the laser: • Attach drywall pin to the wall per instructions under "Drywall Pin" section. Always make sure drywall pin is securely attached to the wall. • Attach the magnetic base (F) of the laser to drywall pin. • Move on/ off switch (D) actuator to the "I" position to project the laser line. • Rotate the laser to center horizontal (H) or vertical (G) bubble vials. Be sure the laser is firmly attached to the drywall pin before removing support. 2). Operation of the laser: • Hold the laser firmly against the wall. • Move on/ off switch (D) actuator to the "I" position to project the laser lines. • Align laser line with appropriate mark on your work surface, rotate the laser to center horizontal (F) or vertical (E) bubble vials. Realign laser with mark if necessary. • Figure...