Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Graco Inc. Dateigröße: 212.4 kb Dateiname: Unterrichtssprache:

. Keep the application area free of debris, including solvent, rags, and gasoline. SKIN INJECTION HAZARD If high-pressure fluid pierces your skin, the injury might look like “just a cut”. But it is a serious wound. Get immediate surgical treatment. To help prevent injection . Keep your hands and body away form the roller frame when flushing. High pressure fluid emitted from the holes in the frame could cause an injection injury. . Always relieve pressure before you check or repair leaks and when you turn off pump or stop painting. . Never use components rated less than system Maximum Working Pressure. ELECTROCUTION HAZARD Failure to observe the electrical hazards described below could result in serious injury, including burns or electrocution. To help prevent harmful electrical shock . Avoid contact with power lines. . Follow all grounding instructions in your separate pump instruction manual, and comply with all local, state, and national fire, electrical, and safety regulations. . Use only Graco paint hoses. 2 309445 Installation Assemble pressure roller as shown in Parts Drawing, . When connecting EvenFlow roller frame to the page 7. Attach pressure roller assembly to inline Contractor Inline Valve, use a wrench to tighten. valve. Pressure Relief Procedure WARNING 3. Turn prime/spray valve to PRIME position to relieve pressure in system. To help prevent injection injuries, follow this procedure whenever 4. Put inline valve trigger safety in SAFETY OFF you stop painting. position, and trigger inline valve to relieve any psi/MPa/bar pressure in hose. 1. Put inline valve trigger safety in SAFETY ON position (Fig. 1). 5. Put inline valve trigger safety in SAFETY ON position, and keep pump prime/spray valve in 2. Shut off power to pump. PRIME position until you paint again. 309445 3 Operation WARNING SKIN INJECTION HAZARD To reduce the risk of a fluid injection injury, do not operate the inline valve with the tip guard or trigger guard removed. In-Line Valve Trigger Safety Lever For SAFETY ON position, rotate trigger safety lever so it is in line with trigger. For SAFETY OFF position, flip safety lever so it is 90. to trigger. Fig. 1. NOTE: In the SAFETY ON position the lever sits in a detent which holds it in place. SAFETY ON SAFETY OFF Fig. 1 Startup NOTE: Cleaning NOTE: Follow this procedure to flush the roller frame and inline valve. The pump you are using may have additional flushing steps, such as cleaning filters and screens. See the pump flushing instructions. Leave the roller frame attached to the inline valve for this procedure. . The Contractor Inline Valve can be used as an airless spray gun by attaching a Handtite Guard and RAC5 Switchtip. 1. Follow pump priming instructions using lowest pressure setting at which pump primes. 2. Turn prime/spray valve to SPRAY position. 3. Disengage inline valve safety latch, trigger the inline valve, and roll the surface until paint comes to roller. NOTE: Trigger the inline valve briefly only when you need more paint. Determine how often you must trigger the inline valve to maintain an even paint supply to the roller. 4. Increase pump pressure only if triggering inline valve cannot supply enough paint for your rolling speed. Relieve pressure, page 3, whenever you stop painting. 5. Elevate roller end of extension tube to prevent paint from draining out. Flush pump, inline valve, and roller frame immediately after each use to prevent paint from drying in roller frame and damaging it. Cleaning the EvenFlow Roller Frame 1. Relieve pressure, page 3. 2. Remove roller cover (19) and diffuser (23) from roller frame as follows (see Parts Drawing): a. Using your thumb, press down on clip (5) to release end caps (2 &4), diffuser (23) and roller cover (19) into a pail. b. Remove roller cover (19) from diffuser (23). c. Pull end caps (2 & 4) off diffuser (23). 3. Clean roller cover (19), caps (2 & 4) and diffuser (19) with water or a compatible fluid for oil–based materials. 4. Place roller frame (1) in paint pail. Be sure the holes in roller frame (1) are facing inside the paint pail. 4 309445 5. Prime pump with water or flushing fluid for oil– based materials. Use the lowest pump priming pressure setting. 6. Turn prime/spray valve to SPRAY. NOTE: Perform Step 7 at the lowest pressure possible. 7. Trigger inline valve until flushing fluid begins to dilute the paint. 8. Place roller frame (1) in another bucket and continue flushing until fluid coming out of the roller frame (1) is clear. Cleaning Contractor Inlin...

Herunterladen

Geben Sie zwei Ziffern: