Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Graco Inc. Dateigröße: 250.11 kb Dateiname: Unterrichtssprache:

Fluid Section 1. Lubricate the bearing (21), o-ring (16) and cup seal (20). Put the o-ring (16) on the bearing. Carefully insert the seal (20) into the bearing recess, with the lips of the o-ring facing into the bearing. Be careful not to damage the seal lips. 2. Push the bearing (21) seal end first into the housing (19). Be sure that the grease hole in the side of the bearing lines up with the grease ports in the housing (19). 3. Holding the bearing (21) in place, push the bearing assembly over the shaft (3). 4. Lubricate the main fluid seal (22) and its cavity in the housing (26). Carefully press the seal, lip-first, into the housing. 5. Push the housing (26) and seal (22) over the shaft (3) and up against the bearing housing. 6. Apply Loctite Primer N7649 and Loctite TL242, 243, or equivalent (“blue” Loctite) to the fluid housing screws (23) and loosely install the screws to retain the housings. Do not tighten the screws yet. 7. Insert the gasket (38) and seat (25). These items are reversible and can be installed in either direction. 8. Apply Loctite Primer N7649 and Loctite TL242, 243, or equivalent (“blue” Loctite) to needle (27) and tighten to 15–20 in–lb (1.7–2.2 Nm). 9. Apply air pressure to the CLOSE port, or to the pneumatic trigger valve if installed. This will align the shaft, seal, and bearing. Tighten the fluid housing screws (23) oppositely and evenly to 40–45 in-lbs (4.5–5 Nm). 10. Install the nosepiece (40) with the PTFE o-ring (39), screw (15), and snuff-back ring (41), if used. The snuff-back ring has an internal bevel on one end which faces into the nosepiece. Tighten the nosepiece screws to 15–20 in-lbs (1.7–2.2 Nm). 20 308876 Parts (Models 243482 and 243666 only) 2222222 34 12 13, 14 6 75 4 3 28, 2920212239 27 23 1 4 40 45 2 9 1030 191816 26 3825 2 2 2 2 Tighten oppositely and evenly to 40–45 in-lbs (4.5–5 Nm). 2 Lubricate with grease supplied in the repair kit. 1 1540 Model 243482 3 Tighten to 15–20 in lbs (17–22 Nm) 4 Apply Loctite Primer N7649 and Loctite TL242, 243, or equivalent (“blue” Loctite). Fig. 6 308876 21 Parts (Models 243482 and 243666 only) 1 19 18 26 30 12 9 10 16 19 7 6 5 3 4 28, 29 20 21 22 39 41 23 40 31 38 25 27 45 15 31 Model 243482 40 8371A 22 308876 Parts Model 965767 Hand Held Valve with Pneumatic Trigger Aluminum wetted parts See page 16 for illustration of items 1–44. See page 18 for illustration of items 46–62. Ref. Part No. Description Qty. Ref. Part No. Description Qty. No. No. 1 626702 HOUSING, air cylinder 1 40 626707 NOSEPIECE, aluminum 1 3 626068 SHAFT, air cylinder 1 41* 626060 RING, snuff-back 1 4* 156454 O-RING, 010 buna-n 2 42. 626708 SHAFT, adjustment 1 5* 551181 BEARING, air cylinder 2 43 626709 NUT, adjustment 1 6* 154662 O-RING, 222 buna-n 2 44 100166 NUT, full hex, 10–32 1 7* 552164 DOWEL PIN 1 46 106559 O-RING, No. 905 5 9* 157628 O-RING, 006 buna-n 1 fluoroelastomer 10 626703 PISTON, air cylinder 1 47 106561 SPRING 1 11 626704 CAP, air cylinder 1 48 106560 O-RING, 007 3 fluoroelastomer 12 552163 CLIP, internal 1.75 2 49 178651 SPOOL, 4-way 1 13 102817 SCREW, drive, #0 x 0.25 2 50 626056 HOUSING, air valve 1 14 552161 PLATE, identification 1 51 178652 SPACER, u-shape 1 16*† 103610 O-RING, 014 1 52 178653 SPACER, air valve 2 fluoroelastomer 18 551188 FLUSH GREASE FITTING 2 53 626055 BUSHING, handle 1 19 626705 LUBE HOUSING 1 54 551204 SCREW, 3/8–16 x 3/4 1 20*† 551191 U-CUP, urethane/EPR 1 55 626075 HANDLE 1 21* 626064 BEARING, lube 1 56 626083 TRIGGER 1 22*† 551190 U-CUP, Polymite/EPR 1 57 106551 O-RING, 0.5 x 0.6 1 fluoroelastomer 23. 103926 SCREW, 1/4–20 x 2.25 2 58 178654 GUIDE, stem 1 25* 185467 SEAT, C2 carbide 1 59 626053 PIN, trigger 1 26 626706 HOUSING, fluid; aluminum 1 60 119156 SCREW, 10–32 x 0.8125 4 27*. 626062 NEEDLE, hardened stain-1 61 100020 WASHER, lock, #10 2 less steel 28. 188377 LABEL, skin injection haz-1 62 104765 PLUG, pipe, headless, 1 ard 1/8 npt (not shown) 29. 188378 LABEL, read instruction 1 * Included in Rebuild Kit 570268. manual 30* 626057 GASKET, air cylinder 1 † Included in Section Seal Kit 570267. 31 104459 SCREW, 10–32 x 1.75 4 35* 115982 GREASE, 3 oz. tube (not 1 . Replacement Instruction and Warning Labels are shown) available at no cost. 36 551189 GUN, grease (not shown) 1 37 551187 COUPLER, flush grease 1 . Loctite Primer N7649 and Loctite TL242, 243, or (not shown) equivalent (“blue” Loctite) should be used when 38*† 171860 GASKET, seat 1 installing this part. 39*† 104319 O-RING, 014 PTFE 1 . Anti–seize lubricant (Loctite 56765 or equivalent) should be used when installing this part. 308876 23 Parts Model 965768 Hand Held Valve with Electric Switch Aluminum wetted parts See page 16 for illustration of items 1–44. See page 18 for illustration of items 53–63. Ref. Part No. Description Qty. Ref. Part No. Description Qty. No. No. 1 626702 HOUSING, air cylinder 1 36 551189 GUN, grease (not shown) 1 3 626068 SHAFT, air cylinder 1 37 551187 COUPLER, flush grease 1 4* 156454 O-RING, 010 buna-n 2 (not shown) 5* ...

Herunterladen

Geben Sie zwei Ziffern: