Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Graco Inc. Dateigröße: 292.27 kb Dateiname: Unterrichtssprache:

(Fig. 5.) Fig. 5 2. With the roller, apply paint to the ceiling, working the short way of the room and applying as wide a strip as possible. (Fig. 6.) Fig. 6 1. Woodwork & Walls: Using a brush, paint woodwork first. Apply a starting row of paint approximately the width of the paint brush around the woodwork and where the walls meet the ceiling. (Fig. 7.) Fig. 7 2. With the roller, apply paint to the walls, following the Roller Techniques described above. (Fig. 8.) Fig. 8 Cleaning This is the procedure for flushing the pressure roller. The pump and gun you are using may have additional flushing steps, such as cleaning filters and screens. See the pump and gun flushing instructions. NOTE: Leave the pressure roller attached to the gun for this procedure. Pressure Relief Procedure, page 3. 1. Relieve the pressure. 2. Remove roller cover (7) and diffuser (4) from roller frame as follows (Parts Drawing, page 7): a. Using your thumb, press down on clip (5) to release end caps (2 & 3), diffuser (4) and roller cover (7) into a pail. b. Remove roller cover (7) from diffuser (4). c. Pull end caps (2 & 3) off diffuser (4). Disassemble. 3. Clean roller cover (7), caps (2 &3) and diffuser (7) with water or a compatible fluid for oil–based materials. 4. Place roller frame (1) in paint pail. Be sure the holes in roller frame (1) are facing inside the paint pail. 5. Prime pump with water or flushing fluid for oil–based materials. Use the lowest pump priming pressure setting. 6. Turn prime/spray valve to SPRAY. NOTE: Perform Step 7 at the lowest pressure possible. 7. Trigger gun until flushing fluid begins to dilute the paint. 8. Place roller frame (1) in another bucket and continue flushing until fluid coming out of the roller frame (1) is clear. 9. Shut off the pump. Turn prime/spray valve to PRIME. Storage If you are going to store the airless equipment for an extended period of time after flushing with water-base fluid, flush again with Graco Pump Armor or mineral spirits/paint thinner. Leave the fluid in the system during storage. . . Roller Parts ti2135b 1 4 3 2 7 5 6, 9 Parts List Ref. No. Part No. Description Qty. 1 FRAME, roller 1 2 245999 CAP, end (includes seal and retainer) 1 3 246277 CAP, end (includes seal and retainer) 1 4 15B065 DIFFUSER 2 o–ring) 1 5 197106 CLIP, roller 1 6 115524 GASKET 1 7 186678 ROLLER, cover, 9 inch, 1/2 in. (13 mm) nap 1 9 197118 SWIVEL, fitting 1 Additional Roller Covers For the best coverage it is important to choose the right roller cover nap for the surface you are rolling. For rougher surfaces choose a thicker nap. Use a thinner nap on smooth surfaces. Part No. Nap Size Surface Texture/ Example Material 243063 9 in. (23 cm); 1/2 in. (13 mm) Smooth/ metal, wood, trim, drywall medium 243064 9 in. (23 cm); 3/4 in. (19 mm) Rough/ cement, brick heavy 243065 9 in. (23 cm); 1-1/4 in. (32 mm) Extra–rough/ cement block, textured walls, ceilings heavy . . Limited Warranty Graco Inc. warrants to the original retail purchaser (other than for purposes of resale or rental) all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship if operated in accordance with Graco’s printed recommendations and instructions. This warranty applies for one year from the date of purchase. This warranty does not cover and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by improper use, accidents, user negligence, use of non-Graco component parts or service or repair performed by anyone other than a Graco authorized service center. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE. GRACO SHALL NOT IN ANY EVENT BE LIABLE FOR ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE OR EXPENSE OF ANY KIND, WHETHER FROM BREACH OF THIS WARRANTY OR ANY OTHER REASON. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. To make a claim under this warranty, return the product with proof of purchase, transportation prepaid, to any Authorized Graco Service Center. Graco’s Authorized Service Center, at its option, will either repair or replace the product and return it to you, postage prepaid. A listing of Authorized Graco Service Centers is enclosed with this product. You may also find the nearest Authorized Graco Service Center by calling 1–888–541–9788 or by visiting our website at This warranty gives you specific legal rights and you may also have other rights which may vary from state to state. All written and visual data contained in this document reflect the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 PRINTED IN USA 309511 4/2002, Revised 4/2003 . . ...

Herunterladen

Geben Sie zwei Ziffern: