Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Black & Decker, modell 5054

Hersteller: Black & Decker
Dateigröße: 4.57 mb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. To determine the minimum wire size required, refer to the following chart. CHART FOR MINIMUM WIRE SIZE (AWG) OF EXTENSION CORDS NAMEPLATE RATING-AMPS TOTAL EXTENSION CORD LENGTH - FEET 25 50 75 100 125 150 175 200 0-10.0 10.1 -13.0 13.1-15.0 18 18 16 16 14 14 12 12 16 16 14 14 14 12 12 12 14 14 12 12 12 12 12 — Before using an extension cord, inspect it for loose or exposed wires, damaged insulation, and defective fittings. Make any needed repairs or replace the cord if necessary. B&D has extension cords that are suitable for outdoor use and UL listed (CSA in Canada) available at extra cost. Side Handle For operating convenience, the side handle can be rotated to any position around the tool (360°). NEVER OPERATE TOOL WITHOUT SIDE HANDLE IN PLACE. Depth Rod To adjust the depth rod, loosen the knob and move rod so that the distance between the end of the rod and the end of the bit equals the desired drilling depth (Figure 1). NOTE: Bit must be fully seated in the hammer when measuring. Figure 2 shows how the depth rod... contacts the work surface when the desired hole depth is reached. Figure 1 TOOL OPERATION Switch The motor is operated by a variable speed trigger switch which, when depressed, turns the tool on. The variable speed switch allows slow starting when hammering for exact hole positioning or when working with brittle surfaces such as glazed tile. The further the trigger is depressed, the higher the R.P.M. (Revolutions Per Minute) and B.P.M. (Beats Per Minute). Releasing the trigger turns the tool off. Changing Bits Your tool is designed for the B&D SDS bit system in sizes from 3/16” to 3/4” diameter. To change a bit: 1. Unplug the unit from power source. 2. Insert the bit with a slight twist. The locking takes place automatically during drilling/hammer drilling. 3. To release bit, pull front end of chuck (Figure 3) and pull bit out. Figure 5 (5014) FWD/REV SWITCH Reversing Switch The hammer is equipped with a reversing switch for backing out jammed drill bits or large screws. 5054 ONLY. To operate the hammer in reverse, slide the lever shown in Figure 4 to the left (when viewed from the chuck end). To operate in forward, slide the lever to the right as shown. 5014 ONLY. To operate the hammer in reverse, slide the button shown in Figure 5 to the right. To operate in forward, slide the button to the left as shown. Always be sure that the tool is off and has stopped coasting before changing its direction. Hammer/Drill Selector Lever (Figure 6) Your hammer is equipped with a selector lever to control drilling or hammering action. 1. Turn the tool off and allow it to stop before shifting. 2. To select “hammer drilling”, rotate the selector lever counterclockwise to the hammer/drill symbol. Hammer Drilling 1. Position selector switch in the “hammer/drill” position. 2. When drilling, use just enough force on the hammer to keep it from bouncing excessively or “rising” off the bit. Too much force will cause slower drilling speeds, overheating, and a lower drilling rate. 3. Drill straight, keeping the bit at a right angle to the work. Do not exert side pressure on the bit when drilling as this will cause clogging of the bit flutes and a slower drilling speed. 4. When drilling deep holes, if the hammer speed starts to drop off, pull the bit partially out of the hole with the tool still running to help clear debris from the hole. 5. Do not pour water into the hole to settle dust. Water causes clogging of bit flutes which will tend to make the bit bind in the hole. Drilling Always unplug the tool when attaching or changing bits or accessories. 1. Use sharp drill bits only. For WOOD, use twist drill bits, spade bits, power auger bits, or hole saws. For METAL, use high speed steel twist bits or hole saws. 2. Be sure the material to be drilled is anchored or clamped firmly. If drilling thin material, use a “back-up” block to prevent damage to the material. 3. Always apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting, but do not push hard enough to stall the motor or deflect the bit. 4. Hold tool firmly to control the twisting action. 5. IF TOOL STALLS, it is usually because it is being overloaded. RELEASE TRIGGER IMMEDIATELY, remove bit from work, and determine cause of stalling. Do not click trigger off and on in an attempt to start a stall...