Login:
Stimmen - 6, Durchschnittliche Bewertung: 4 ( )

Anleitung Black & Decker, modell D25500

Hersteller: Black & Decker
Dateigröße: 323.42 kb
Dateiname:
Unterrichtssprache:enesfr
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


7. Lock the side handle mounting assembly in place by tightening the clamp knob. TO MOUNT IN REAR POSITION (FIG. 2) 1. Unscrew the side handle and remove it from the front position. 4 582429-00/D25500 etc 1/29/03 9:29 AM Page 5 Leave the side handle mounting assembly in front position so that the depth adjustment rod can still be used. 2. Screw the side handle directly into one of the rear side handle positions on either side of the tool. TO ADJUST THE DEPTH ROD 1. Insert bit into tool holder and loosen depth rod clamp 2. Place drill bit onto a surface, adjust the rod to desired depth Using the depth rod will allow you to drill a hole the depth distance between the bit and the depth rod tip. 3. Tighten clamp nut. NOTE: This adjustment can be made with or without side handle in place. Inserting and Removing Spline Drive Accessories FIG. 3: (D25550, D25551, D25650, D25850) TURN OFF TOOL AND DISCONNECT FROM POWER SUPPLY. 1. Unlock the tool holder by pushing the retaining pin button (J) and holding it in. 2. Insert the bit shank into the tool holder as far as it will go. FIG. 3 started with the drill bit in an existing hole. Torque Limiting Clutch and cannot be adjusted. (Fig. 5) FIG. 4 5 3. Release the retaining pin button. 4. Pull on the bit to be sure that it is properly 5. To remove a bit unlock the tool holder as described Inserting and Removing SDS-maxAccessories FIG. 4: (D25500, D25600, D25830) TURN OFF TOOL AND DISCONNECT FROM POWER SUPPLY. 1. Pull back the tool holder locking sleeve (A) and insert the 2. Turn the bit slightly until the sleeve snaps back in position. 3. Pull on the bit to be sure that it is properly locked. The hammering function requires the bit to be able to move axially several centimeters when locked in the tool holder. 4. To remove bit, pull back the tool holder locking sleeve and pull the bit out of the tool holder. FIG. 5 Soft Start Feature (All Models) The soft start feature allows you to build up speed slowly, thus preventing the drill bit from walking off the intended hole position when starting. The soft start feature also reduces the immediate torque reaction transmitted to the gearing and the operator if the hammer is G All rotary hammers are equipped with a torque limiting clutch that reduces the maximum torque reaction transmitted to the operator in the case of a jamming drill bit. This feature also prevents the gearing and motor from stalling. The torque limiting clutch has been factory set Electronic Speed and Impact Control The electronic speed and impact control allows the use of smaller drill English 582429-00/D25500 etc 1/29/03 9:29 AM Page 6 English bits without the risk of bit breakage, materials without shattering, and optimal chiseling. To set the control dial, turn the dial to the desired higher the number, the greater the speed and impact energy. Dial settings make the tool extremely flexible and different applications. The required setting depends on the bit size and hardness of material being drilled. Mode Selector (Fig. 6 & 7) Your rotary hammer (all units except D25550) can be used in two operating modes. In hammer drilling mode, the t...

Dieses Handbuch ist für folgende Modelle:
Andere Werkzeuge - 582429-00 (323.42 kb)
Andere Werkzeuge - D25550 (323.42 kb)
Andere Werkzeuge - D25551 (323.42 kb)
Andere Werkzeuge - D25600 (323.42 kb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien