Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
You can ATTENTION: avoid the potential hazards identified on this machine by following the procedures outlined below and elsewhere in the READ THIS SO NO User Guide. ONE GETS HURT WARNING: Improper installation, operation or servicing may result in equipment damage or personal injury. This equipment should be installed, adjusted, and serviced by qualified technical personnel who are familiar with the construction, operation and potential hazards of this type of equipment. All wiring, disconnects and fuses should be installed by qualified electrical technicians in accordance with electrical codes in your region. Always maintain a safe ground. A properly sized conductive ground wire from the incoming power supply must be connected to the chassis ground terminal inside the electrical enclosure. Improper grounding can result in personal injury and erratic machine operation. Do not operate the equipment at power levels other than what is specified on the the equipment serial tag and data plate. WARNING: Electrical shock hazard This equipment is powered by single-phase main voltage, as specified on the machine serial tag and data plate. Always disconnect and lock out the incoming main power source before opening the electrical enclosure or performing non-standard operating procedures, such as troubleshooting or maintenance. Only qualified personnel should perform procedures that require access to the electrical enclosure while power is on. WARNING: Disconnect power and air sources. Always disconnect the man power source and compressed air source before installing or servicing this equipment. This prevents the equipment from starting during servicing, which could cause personal injury from flying debris or moving parts. CAUTION: Wear eye protection We recommend that you use vacuum air for cleaning filters and other parts of this equipment. If you use compressed air to clean the equipment, you must wear eye protection and observe all OSHA and other safety regulations pertaining to the use of compressed air. Conair has made the largest investment in customer support in the plastics industry. Our service experts are available to help with any problem you might have installing and operating your equipment. Your Conair sales representative also can help analyze the nature of your problem, assuring that it did not result from misapplication or improper use. To contact Customer Service personnel, call: From outside the United States, call: 814-437-6861 You can commission Conair service personnel to provide on- site service by contacting the Customer Service Department. Standard rates include an on-site hourly rate, with a one-day minimum plus expenses. If you do have a problem, please complete thefollowing checklist before calling Conair: . Make sure you have all model, serial and parts list numbers for your particular equipment. Service personnel will need this information to assist you. . Make sure power is supplied to the equipment. . Make sure that all connectors and wires within and between loading control and related components have been installed correctly. . Check the troubleshooting guide of this manual for a solution. . Thoroughly examine the instruction manual(s) for associated equipment, especially controls. Each manual may have its own troubleshooting guide to help you. . Check that the equipment has been operated as described in this manual. . Check accompanying schematic drawings for information on special considerations. WE’RE HERE TO HELP HOW TO CONTACT CUSTOMER SERVICE BEFORE YOU CALL ... Additional manuals and prints for your Conair equipment may be ordered through the Customer Service or Parts Departments for a nominal fee. SERVICE INFORMATION APPENDIX A-1 EQUIPMENT GUARANTEE PERFORMANCE WARRANTY WARRANTY LIMITATIONS Conair guarantees the machinery and equipment on this order, for a period as defined in the quotation from date of shipment, against defects in material and workmanship under the normal use and service for which it was recommended (except for parts that are typically replaced after normal usage, such as filters, liner plates, etc.). Conair’s guarantee is limited to replacing, at our option, the part or parts determined by us to be defective after examination. The customer assumes the cost of transportation of the part or parts to and from the factory. Conair warrants that this equipment will perform at or above the ratings stated in specific quotations covering the equipment or as detailed in engineering specifications, provided the equipment is applied, installed, operated and maintained in the recommended manner as outlined in our quotation or specifications. Should performance not meet warranted levels, Conair at its discretion will exercise one of the following options: Inspect the equipment and perform alterations or adjustments to satisfy performance claims. (Charges for such inspections and corrections will be waived unless failure to meet warranty is due to misapplication, improp...