Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it. CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Side handle (auxiliary handle) The side handle can be secured in any position. Loosen the nut and swing the side handle to the desired position. Then tighten the nut firmly to secure the side handle. If the set bolt turns together with the nut when you turn the nut, set the set bolt so that the projecting portion of the side handle is fitted into the notch in the bolt head. 002932 1 2 002932 1 2 1. Bull point 2. Tool retainer 002933 1 1. Boss OPERATION MAINTENANCE 001146 1 2 3 1. Commutator 2. Insulating tip 3. Carbon brush Installing or removing the bit Pull out and turn the tool retainer so that the boss on the tool retainer faces in the direction of the arrow. Insert the bit into the tool holder as far as it will go. Then pull out and turn the tool retainer 180 degrees to secure the bit. To remove the bit, follow the installation procedure in reverse. Chipping/Scaling/Demolition Hold the tool firmly with both hands. Turn the tool on and apply slight pressure on the tool so that the tool will not bounce around, uncontrolled. Pressing very hard on the tool will not increase the efficiency. CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes When the resin insulating tip inside the carbon brush is exposed to contact the commutator, it will automatically shut off the motor. When this occurs, both carbon brushes should be replaced. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. 002957 Use a screwdriver to remove the holder cap plates. 1 2 002957 Use a screwdriver to remove the holder cap plates. 1 2 1. Screwdriver 2. Holder cap plate 1 2 1. Screwdriver 2. Brush holder cap 002958 Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. 1 2 1. Screwdriver 2. Plate 50 002972 Lubrication This tool requires no hourly or daily lubrication because it has a grease-packed lubrication system. It should be relubricated after every 6 months of operation. Send the complete tool to Makita Authorized or Factory Service Center for this lubrication service. However, if circumstances require that you should lubricate it by yourself, proceed as follows. First, switch off and unplug the tool. 002973 Remove the plate 50 using a screwdriver, then replenish with fresh grease (60 g; 2 oz). Use only Makita genuine hammer grease (optional accessory). Filling with more than the specified amount of grease (approx. 60 g; 2 oz) can cause faulty hammering action or tool failure. Fill only with the specified amount of grease. Reinstall the plate 50 and secure with the screws. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 1 1. Hammer grease ACCESSORIES ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita service center. • Bull point • Cold chisel • Scaling chisel • Clay spade • Rammer • Safety goggles • Hammer grease • Hex wrench • Steel carrying case Memo Memo Memo Memo Memo Cut Cut s Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: Home Center Other ( Hardware/Lumber Store Tool Distributor Industrial Supply Construction Supply 2. Use of the product is intended for: Construction Trade Industrial Maintenance Home Maintenance Hobby Other ( ) 5. Any comments: 3. How did you learn about this product: ) Magazine Radio From Dealer Exhibition Newspaper From Friend Store Display Previous Usage Catalog Other ( ) 4. Most favored points are: Design Repair Service Features Durability Size Power Price Other ( ) Makita Brand BE SURE TO COMPLETE THE CUSTOMER’S PORTION OF THIS FORM AND RETAIN FOR YOUR RECORDS. DATE PURCHASED MODEL NO. SERIAL NO. INTL. LAST NAME / COMPANY NAME STREET ADRESS CITY STATE AGE: ZIP CODE PHONE AREA CODE STATUS Married SEX M FSingle MONTH DAY YEAR Under 19 20-29 30-39 40-49 50-60 Over 60 Please return this portion by facsimile or mail. Facsimile No: (714) 522-8133 Paste Paste Paste Paste Paste Paste Paste P...