Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
FUNCTIONAL DESCRIPTION 002892 1 1. Switch lever ASSEMBLY 002928 1 2 1. Bit with collar 2. Bit without coller CAUTION: • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Switch action CAUTION: • Before plugging in the tool, always check to see that the switch lever actuates properly and returns to the “OFF” position when released. To start the tool, simply squeeze the switch lever. Release the switch lever to stop. CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Installing or removing the bit This tool accepts bits either with or without a collar on its shank. To install the bit, follow either procedure (1) or (2) described below. (1) For bits with a collar 002934 1 2 3 4 5 Fig.(1) 1. Bit2. Tool retainer 3. Tool holder4. When the bit is inserted 5. When the bit is retained Pivot the tool retainer back and slightly downward. Insert the bit into the tool holder as far as it will go. To securely retain the bit, return the tool retainer to its original position. • Always assure that the bit is securely retained by attempting to pull the bit out of the tool holder after completing the above procedure. (2) For bits without a collar 1. Notched portion 2. Tool retainer shaft 1 2 3 4 5 Fig.(2) 002931 3. Cylinder 4. When the bit is inserted 5. When the bit is retained Pivot the tool retainer front and slightly downward. With the notched portion of the bit facing the tool retainer shaft, insert the bit into the tool holder as far as it will go. Then pivot the tool retainer further downward toward the cylinder to securely retain the bit. CAUTION: • Always assure that the bit is securely retained by attempting to pull the bit out of the tool holder after completing the above procedure. • The bit without a collar cannot be retained by the method shown in Fig.(1). To remove the bit, follow the installation procedure in reverse. OPERATION Chipping/Scaling/Demolition Hold the tool firmly with both hands. Turn the tool on and apply slight pressure on the tool so that the tool will not bounce around, uncontrolled. Pressing very hard on the tool will not increase the efficiency. MAINTENANCE 001146 1 2 3 1. Commutator 2. Insulating tip 3. Carbon brush 002959 1 2 1. Hex wrench 5 2. Motor housing cover 002960 2 1 1. Brush holder cap 2. Screwdriver CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes When the resin insulating tip inside the carbon brush is exposed to contact the commutator, it will automatically shut off the motor. When this occurs, both carbon brushes should be replaced. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. Use a hex wrench to remove the motor housing cover. Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. 002974 1 2 002974 1 2 1. Screwdriver 2. Plate 50 002975 1 1. Hammer grease ACCESSORIES Lubrication This tool requires no hourly or daily lubrication because it has a grease-packed lubrication system. It should be relubricated after every 6 months of operation. Send the complete tool to Makita Authorized or Factory Service Center for this lubrication service. However, if circumstances require that you should lubricate it by yourself, proceed as follows. First, switch off and unplug the tool. Remove the plate 50 using a screwdriver, then replenish with fresh grease (60 g; 2 oz). Use only Makita genuine hammer grease (optional accessory). Filling with more than the specified amount of grease (approx. 60 g; 2 oz) can cause faulty hammering action or tool failure. Fill only with the specified amount of grease. Reinstall the plate 50 and secure with the screws. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita service center. • Bull point • Cold chisel • Scaling chisel • Clay spade • Rammer • Safety goggles • Hammer grease • Hex wrench • Wooden carrying case Memo Memo Memo Memo Memo Cut Cut Stamp Timbre Makita Canada Inc. 1950 Forbes Street, Whitby, Ontario L1N 7B7 Fold Your answers to the following questions are appreciated. Your answers to the following questions are appreciated. This product was purchased from? Hardware/lumber Store Industrial Supply Tool Distributor Other ( ) 2. Use of the produ...