Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
NOTE: The cleaning solution will depend on the type of paint being used. See specific cleaning instructions on page 9. 2. Remove the Spatter Shield (46) by pulling it off the Paint Roller assembly. Remove the Paint Roller (43) and Roller Spindle (44) from the Roller Arm (39). To do this, press down the lever on the Locking Tab (38), then pull the Paint Roller Assembly off the Roller Arm. 3. Further disassemble the Roller Assembly by placing your thumb into the opening in the Roller Bushing (42), and pry it out of the Paint Roller (43). Place the Paint Roller components into a bucket or sink prior to being washed. 4. Remove the Paint Can Lid (13) and place it in the bucket for cleaning. 5. Hold the Roller Arm (39) over the open Paint Can (12).With the Selector Switch turned to the “Paint” setting, press the Handle Button (24) to pump paint remaining in the tool back into the Paint Can. Stop pumping by releasing the Handle Button (24) when the paint has been pumped through and cleaning fluid starts to come out of the Roller Arm (39). Selector Switch (02) REV 02/07 SKU 93359 For technical questions, please call 1-800-444-3353 Page 8 Cleanup for Latex Paint After purging the Paint Roller, use these steps for latex paints only. 1. Place a large empty bucket on a counter or shelf higher than the container of cleaning solution.Warm soapy water is recommended for latex paints. Be sure the empty bucket has greater capacity than the container of water. 2. Hang the Roller Arm (39) onto the empty container so that water pumped through it will flow into the container. 3. Move the Selector Switch to the “Clean” position.This will cause the Pump (15) to operate without pressing the Handle Button (24). 4. While the unit is self-cleaning, HAND CLEAN the Paint Roller (43), Roller Core (45) and Spatter Shield (46). 5. When all the cleaning solution has been pumped through, elevate the Main Unit above the Handle Assembly and continue to run the Pump Assembly (15) until all the cleaning solution has been purged from the unit. 6. Move the Selector Switch to “Off” and unplug the unit. NOTE: Some paint residue will remain in the tubes, but this will not harm the unit or impair future painting performance. 7. If you are using the Extension, press the tabs on the Roller Arm Coupling (35) of the Extension Tube (34) and pull out the Roller Arm (39). Press the tab on the Handle Connector (27) and remove the Extension Tube (34). 8. If you are not using the Extension, press the tab on the Handle Connector (27) and remove the Roller Arm (39). 9. Clean the Handle unit with a damp cloth.CAUTION:DO NOT IMMERSE THE HANDLE UNIT, AS IT WILL BE DAMAGED. Cleanup for Oil Based Paint After purging the Paint Roller, use these steps for oil based paints only. 1. Place the Roller Arm (39) and Suction Tube (14) in a bucket of mineral spirits or other appropriate paint cleaner. 2. Move the Selector Switch to the “Clean” position.This will cause the Pump (15) to operate without pressing the Handle Button (24). 3. While the unit is self-cleaning, HAND CLEAN the Paint Roller (43), Roller Core (45) and Spatter Shield (46). 4. After the unit has run for 10 or more minutes, and is clean, follow steps 1-3 for cleaning latex based paint as listed above. 5. When all the cleaning solution has been pumped through, elevate the Main Unit above the Handle Assembly and continue to run the Pump Assembly (15) until all the cleaning solution has been purged from the unit. 6. Move the Selector Switch to “Off” and unplug the unit. NOTE: Some paint residue will remain in the tubes, but this will not harm the unit or impair future painting performance. CAUTION: When starting on a new paint project, first purge any solvents or paint pigments in the tubes from the previous clean up. 7. If you are using the Extension, press the tabs on the Quick Release Unit (35) of the Extension Tube (34) and pull out the Roller Arm (39). Press the tab on the Handle Connector (27) and remove the Extension Tube (34). 8. If you are not using the Extension, press the tab on the Handle Connector (27) and remove the Roller Arm (39). 9. Clean the Handle unit with a damp cloth.CAUTION:DO NOT IMMERSE THE HANDLE UNIT, AS IT WILL BE DAMAGED . REV 02/07 SKU 93359 For technical questions, please call 1-800-444-3353 Page 9 Proper Disposal of Paint and Materials 1. Unused paint and solvents must be disposed of properly. DO NOT simply dump them on the ground or down a sink. Check with your local authority for appropriate disposal practices and sites in your area. 2. Do not allow children or unauthorized persons to have access to unused paints, solvents and related materials. These may be harmful or poisonous, potentially causing serious personal injury. Always keep such materials properly and safely stored. 3. Do not store oily rags in a closed container. WARNING: Oily rags in a closed container or confined area may spontaneously combust. Such materials may start on fire on their own because of the chemicals...