Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Should it become necessary to loosen or remove any hydraulic fittings, lines or reservoir cap, be sure to relieve all. pressure by shutting of the engine and moving the control handle back and forth several times.. NEVER remove the cap from the hydraulic tank or reservoir while the unit is running. Hot oil under pressure. could result in serious injury. See also SAFETY PERCAUTIONS.. The pressure relief valve on your splitter is preset at the factory. DO NOT adjust the valve. Only a qualified. technician should perform this adjustment.. 7 MAINTENANCE AND STORAGE. WARNING: DISCONNECT THE SPARK PLUG BEFORE PERFORMING ANY MAINTENANCE.. Consult the operating and maintenance instructions of the engine manufacturer for engine care.. Always check the oil level of the hydraulic reservoir before operation. Operating without an adequate oil. supply will cause severe damage to the pump.. Periodically check that all nuts, bolts, screws, clamps and fittings are tight and secure.. To keep your splitter in top working condition perform all recommended maintenance procedures before you use. your splitter.. If the wedge becomes dull or nicked a grinder or sharpening tool can be used to sharpen it.. Completely drain the fuel tank prior to storage. Always store gasoline in an approved, tightly sealed container. Store. container in a dry, cool place with adequate ventilation. Keep fuel away from areas where fumes could contact open. flame, pilot light or sparks.. Be aware of the environment when disposing of used petroleum products. Please dispose of used hydraulic. fluid, engine oil and any by products from the maintenance of your splitter at approved recycling centers.. Should it become necessary to disassemble the unit for repair or replacement of parts, refer to the drawings and parts. list on the following pages. Exercise extreme caution, as some parts are very heavy and will require sufficient. persons or mechanical handling equipment.. Your Swisher Log Splitter has been produced with components designed specifically to this machine. Although. standard springs, hardware and ect may look similar to parts used on other machinery, they may in some cases. be made of a different construction and/or materials. All replacement parts must meet manufacturer’s. specifications.. The operation of any splitter can produce foreign objects to be thrown into the. eyes, resulting in severe eye damage. Always wear certified safety glasses or. wide-vision safety goggles over spectacles before staring any splitting machine. and while operating such a machine. The operation of any splitter produces sound waves that are damaging to the. human ear. Ear protection is recommended. 8 SAFETY DECALS . Replace decals immediately if damaged. OD16 – FUEL SHUT OFF DECAL OD07 – COLD WEATHER DECAL (NOT ALL MODELS) OD12 – HYDRAULIC FILL PLUG. 11794 – CAUTION DECAL DECAL OD33– SPEED DECAL 11427 – LS DANGER DECAL 9 ASSEMBLY DETAILASSEMBLY DETAIL LS722X MODELS 10 SERVICE PARTS Please have Model and Serial Numbers ready when ordering parts. Color cannot be guaranteed upon service parts. ITEM NUMBER DESCRIPTION PART NUMBER 1 54" Return Hose 7290 2 48" Pressure Hose 7289 3 #12 Hose Clamp LS5001 4 Return Line Fitting 7329 5 Filter Head LS1112 6 Filter Element LS1113 7 3/4" NPT Filler Cap w/Hole 7379 8 Hydraulic Reservoir/Tank 11467TK 9 Bolt 3/8-16 X 3/4 Serr Flange NB780 10 Nut 3/8-16 Serr Flange NB779 11 Bolt 5/16-18 X 3/4 Serr Flange NB596 12 Nut 5/16-18 Serr Flange NB170 13 #16 Hose Clamp LS4999 14 20" Suction Hose 7346 15 Hydraulic Pump-LS722X LS2001H 16 Pressure Line Fitting 11248 17 Motor Base Weldment 11207TK 18 Tongue Support Weldment 11373TK 19 3/8 X 2 1/2 Safety Hitch Pin H11 20 Bolt 3/8-16 X 2 1/2 GR 5 NB619 21 Washer 3/8 SAE NB272 22 Nut 3/8-16 Nyloc NB182 23 Tongue Weldment 11374TK 24A Leg Support Bracket 1 11372TK 24B Leg Support Bracket 2 11425TK 25 Leg Weldment 11371TK 26 5/16-18 Special Hex Flange Shoulder Bolt NB743 27 Additional Support Weldment 11615TK 28 Washer 5/16 SAE NB275 29 Nut 5/16-18 Nyloc NB181 30 5/16 X 1 Ball Lok Pin - Ring Grip 11619 30A Plastic Lanyard NB652 30B Bolt 1/4-20 X 1/2 MSC ZP NB114 30C Nut 1/4-20 Serrated Flange NB524 31 Bolt 3/8-16 X 1 1/2 GR 5 NB107 32 1/8 X 1/2 #3 Woodruff Key 024002 33 Pump Pulley 7306 34 5/16-18 X 1/2 Set Screw w/Loctite NB312 35 37" Belt 11399 36 Idler Bushing 6037 37 Idler Arm 6041TK 38 Idler Spacer 6040 39 Idler Pulley B527 40 Nut 3/8-16 2-Way Lock NB280 41 Clutch Lever 11226TK 42 Handle Grip 2077 43 Clutch Spring 682S 44 Bolt 3/8-16 X 5 Turned Eye 11223 45 Tension Strap 11376TK 46 Axle Weldment 11370TK 47 Tire & Wheel F4157WF 48 Washer 3/4ID X 1 1/4OD 10GA NB184 49 Cotter Pin 1/8" X 1" NB126 11 BEAM DETAILBEAM DETAIL ITEM NUMBER DESCRIPTION PART NUMBER Beam W eldment 11468TK W edge W eldment 11910TK W edge GIB Angle 11857TK Bolt 3/8-16 X 1 1/4 Carriage 10501 Nut 3/8-16 Nyloc NB182 Nut 1/2-13 Nyloc Jam NB121 1/2-13 X 3 1/2 GR5 ZP NB577 Ram Cylinder 11242TK 2-W ay Pipe Nipple 7292 Hydraulic Fitti...