Stimmen - 4, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: DeWalt Dateigröße: 902.76 kb Dateiname: Unterrichtssprache:

The red indicator LED (W) flashes if there is a fault with the tool or if the brushes are completely worn (refer to Brushes under Maintenance). OPERATION WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/installing attachments or accessories. WARNING: To reduce the risk of personal injury, ALWAYS ensure workpiece is anchored or clamped firmly. If hammerdrilling thin material, use a wood “back-up” block to prevent damage to the material. WARNING: To reduce the risk of personal injury, ALWAYS operate the tool with the side handle properly installed and securely tightened. Failure to do so may result in the side handle slipping during tool operation and subsequent loss of control. Hold tool with both hands to maximize control. Proper Hand Position (Fig. 1) WARNING: To reduce the risk of serious personal injury, ALWAYS use proper hand position as shown. WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation of a sudden reaction. Proper hand position requires one hand on the side handle (C), with the other hand on the main handle (D). NOTE: Operating temperature of this tool is 19° to 104° F (-7 to +40° C). Using the tool outside of this temperature range will decrease the life of the tool. Trigger Switch (Fig. 1) To turn the tool on, depress the trigger switch (A). To stop the tool, release the trigger switch. D25602, D25651 In chipping mode only, lock the trigger switch on, push the lock-on slider (B) upwards while depressing the trigger switch. To deactivate the lock-on slider, depress the trigger switch once then release. The lock-on slider may only be activated in chipping mode. The machine will stop running when trying to engage the lock-on slider in hammerdrilling mode. The motor will stop if the lock-on slider is activated when changing from chisel mode into hammerdrilling mode. D25831, D25851 For continuous operation, move the toggle switch to the on position. To stop continuous operation, move the toggle switch to the off position. HAMMERDRILLING MODE MODE DE MARTEAU PERFORATEUR MODO TALADRO PERCUTOR CHIPPING MODE MODE DE BURINAGE MODO CINCEL CHISEL BIT ADJUSTMENT MODE MODE DE REGLAGE DU TREPAN ORDINAIRE MODO DE AJUSTE DE LA BROCA DE CINCEL CHISEL BIT ADJUSTMENT MODE MODE DE REGLAGE DU TREPAN ORDINAIRE MODO DE AJUSTE DE LA BROCA DE CINCEL F E A I G B E C H D FIG. 1 K J O H C N FIG. 2 P L M FIG. 3 C I D25602 W CTC COMPLETE TORQUE CONTROL DEWALT INDUSTRIAL TOOL CO., BALTIMORE, MD 21286 USA FOR SERVICE INFORMATION, CALL 1-800-4-DEWALT SER. D25XXX 1 3/4" (44mm) SDS MAX ROTARY HAMMER AFIN DE MINIMISER LES RISQUES DE BLESSURES, L’UTILISATEUR DOIT LIRE LE GUIDE D’UTILISATION.TOUJOURS UTILISER UNE PROTECTION OCULAIRE, AUDITIVE ET RESPIRATOIRE ADEQUATE. UTILISER LA POIGNEE LATERALE. LEA EL MANUAL DE INSTRUCCIONES PARA UN FUNCIONAMIENTO SEGURO. SIEMPRE UTILICE PROTECCION ADECUADA PARA LOS OJOS, OIDOS Y VIAS RESPIRATORIAS. SIEMPRE UTILICE EL MANGO LATERAL. TO REDUCE THE RISK OF INJURY, USER MUST READ INSTRUCTION MANUAL. ALWAYS USE PROPER EYE, EAR AND RESPIRATORY PROTECTION. ALWAYS USE SIDE HANDLE. Service Lock-On Brush Service WARNING AVERTISSEMENT ADVERTENCIA FIG. 5 G V S T U FIG. 4 M P R Q J SOFT START FEATURE The soft start feature allows you to build up speed slowly, thus preventing the drill bit from walking off the intended hole position when starting. The soft start feature also reduces the immediate torque reaction transmitted to the gearing and the operator if the hammer is started with the drill bit in an existing hole. Hammerdrilling with a Solid Bit D25501, D25553, D25602, D25651 NOTE: The D25831, D25851 have only chipping modes with no hammerdrilling capability. 1. Set the mode selector (F) to hammerdrilling mode. 2. For D25602 and D25651 only, move the torque control lever (U) to Setting 1 (S). 3. Set the speed and impact control dial (G). 4. Insert the appropriate drill bit. 5. Adjust the side handle (front or rear position) (C). 6. Mark the spot where the hole is to be drilled. 7. Place the drill bit on that mark and depress the trigger switch (A). 8. Apply only enough pressure to engage active vibration control (refer to Active Vibration Control). 9. To stop the tool, release the trigger switch. Always turn the tool off when work is finished and before unplugging. Hammerdrilling with a Core Bit D25501, D25553, D25602, D25651 CAUTION: Do not use a core bit for hammerdrilling wood. Personal injury and damage to tool may result. NOTE: The D25831, D25851 have only chipping modes with no hammerdrilling capability. 1. Set the mode selector (F) to hammerdrilling mode. 2. For D25602 and D25651 only, move the torque control lever (U) to Setting 2 (T). 3. Turn the speed and impact control dial (G) to the maximum speed (level 7). 4. Adjust the side handle (front or rear position) (C). 5. Assemble the centering bit and adapter shank into core bit. 6. Mark th...

Herunterladen

Geben Sie zwei Ziffern: