Stimmen - 3, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
All Rights Reserved. Owners Manual and Safety Instructions Table of Contents A. Introduction . . . . . . . . . . . . . . . . . . . . . . . .1 B. Log Splitter Specification . . . . . . . . . . . . .1 C. Unpacking and Assembly Instructions . .2 D. Service Information . . . . . . . . . . . . . . . . .5 E. Special Safety Information . . . . . . . . . . . .5 1. Safety Decals . . . . . . . . . . . . . . . . . . . . . . . .5 2. Safety Warnings . . . . . . . . . . . . . . . . . . . . . .7 3. Important extension cord information . . . . .8 4. Always disconnect power cord from power source . . . . . . . . . . . . . . . . . . . . . . . . .8 5. Hydraulic Safety . . . . . . . . . . . . . . . . . . . . . .8 F. Before You Start Splitting . . . . . . . . . . . .9 G. Operation . . . . . . . . . . . . . . . . . . . . . . . . .11 H. Removal of logs jammed on the wedge . . .12 I. How to change the hydraulic oil . . . . . .13 J. Sharpening the wedge . . . . . . . . . . . . . . .14 K.Transport . . . . . . . . . . . . . . . . . . . . . . . . .15 L. Maintenance . . . . . . . . . . . . . . . . . . . . . .15 M.Troubleshooting . . . . . . . . . . . . . . . . . . . .17 N. Storage . . . . . . . . . . . . . . . . . . . . . . . . . . .17 O. Exploded View and Parts List . . . . . . . .18 P. Declaration of Conformity . . . . . . . . . . .20 Q. Mantis Warranty Policy . . . . . . . . . . . . .21 A. Introduction The SwiftSplit log splitter is designed for residential (noncommercial) use and makes your job less physically demanding, more efficient and safer. With a log splitter, the log is split when pressed against a fixed splitting wedge by a pressure plate. Major Components, Controls, and Features Overview: An electric motor assembly provides the power for the system. The motor is connected to a hydraulic oil pump that creates a flow of high-pressure oil which runs to a solenoid valve. A switch set and the solenoid valve let the operator actuate the hydraulic cylinder to split a log. An internal reservoir holds the hydraulic oil that feeds the pump. The hydraulic assembly is attached to the wheel frame assembly, making it easy to move the log splitter around with no lifting. The frame is equipped with folding handles for storage, pivoting support for stability and cord storage hooks for convenience. This log splitter is designed with two hand operating controls (two normally open switches) for safety. The electrical motor is protected by a 15 amp circuit breaker. The pressure relief valve protects the hydraulic assembly. When the log is jammed, relief valve will prevent pressure from going over its maximum allowable level. B. Log Splitter Specification for Model #5005 Maximum Output Force 10,000 lbs (5 tons) Total Stroke (in)- Ram Travel 15. Total Weight 135 lbs (61 Kg) L x W x H 40. L x 20. W x 38. H Voltage 120V Motor 1.8 kW Motor RPM Max 3380 RPM Maximum Log Length 20. (520mm) Recomd. Maximum Log Diameter 12. Dia. Wheel Size 10. Dia. Wedge Vertical Beam Log Guides Pressure Plate Two Switches Folding Handle Wheel Frame Assembly Cord Storage Hooks Connecting Link Stabilizing Bar / Pivoting Support 2 C. Unpacking and Assembly Instructions 1. Cut bands; remove cover and two inserts supporting the top and the bottom of the unit. Remove wheels, pivoting support and hardware box from the box. 2. Put log splitter in the vertical position by holding the top of the beam and carefully lifting the top of the log splitter until it can stand. 10 HARDWARE BAG PIVOTING SUPPORT #520104 (QTY=1) WHEELS #520102 (QTY=2) LOG SPLITTER WITH ATTACHED HANDLE 3 3. Check contents of the hardware bag. 31 29 28 2 3 9 8 7 9 11 14 9 14 11 8 3 28 29 111 31 7 KNOB CABLE TIE 152MM (6") LONG 2 520101 1 1 2 2 520516 520116 520510 WHEEL SHAFT M14 WHEEL NUT ALLEN WRENCH 8MM (DRAIN PLUG) 2 2 4 2 2 520503 520501 520505 520105 520502 BOLT HEX M6 x 30mm CONNECTING LINK NUT LOCK M6, NYLON INSERT WASHER FLAT 06 BOLT HEX M6 x 40mm 2 2 520500 M10 CARRIAGE BOLT,SQUARE NECK, 60mm LONG 520117 ITEM NO. QTY PART NO. DESCRIPTION HARDWARE BAG #520517 (QTY=1) 111 25 25 1 520113 DIP STICK SEAL (SPARE) 4 4. Folding Handle: Install the folding handle onto the frame using knobs (P/N 520101) and carriage bolts (P/N 520500). To do this, align square opening of the folding handle with the frame.s round hole and insert carriage bolt through. Secure it with the handle knob. Repeat the same steps for the opposite side of the handle and tighten the knobs. 5. Use cable ties (P/N 520117) to secure the power cord in place. 6. Installing Wheels: Insert the Wheel Shaft (P/N 520116) in the hub of the Wheel and secure it with the Nut (P/N 520510) provided. Slide the opposite side of the Wheel Shaft through the opening in the frame and bracket, then screw, it into the welded nut. Start by hand and then use a wrench and secure the wheel. Repeat these steps to install the second wheel. 7. Pivoting Support Installation: Align mounting hole of the Pivoting Support (P/N 520104) with the frame hole, insert Bolt (P/N...