Stimmen - 5, Durchschnittliche Bewertung: 4 ( )

Hersteller: Delta Dateigröße: 8.55 mb Dateiname: 3ea861b5-60d0-4da3-a50b-cd8334cdea66.pdf Unterrichtssprache:

Water) Maximum Hose Velocity PPM Bag Area in Sq. Ft. dBA " Hose Size Drum Size 50-180 1 HP 1 Ph. 115/230 60-3450 700 4Vz" 5131 19.0 83. 5" x 60" 55 Gal. 50-181 2 HP 1 Ph. 230 60-3450 1100 8 W 5600 19.0 85 6" x 60" 55 Gal. 50-182 3 HP 3 Ph. 230/460 60-3480 ! 1300 10» 6619 50.0 84 6" x 60" 55 Gal. / - - ’ . ■' - ' • ■" DATED 11-28-94 " . - PART NO. 410-06-651-0001 © Delta International Machinery Corp. 1994 READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR SERVICE YOUR DUST COLLECTOR! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. SAFETY RULES 1. Follow all local electrical and safety codes, as well as the National Electric Code (NEC) and the Occupational Safety and Health Act (OSHA). All electrical connections and wiring should be performed by qualified personnel only. 2. National Fire Protection Association (NFPA) standards require specific duct design and dust collector configuration when collecting potentially reactive metal dusts, such as aluminum and magnesium. Consult current NFPA standards before setting up a dust collector and/or duct design for these two materials. 3. Use only 3-wire extension cords which have 3 prong grounding type plugs and are of adequate size for longer runs. 4. Replace or repair damaged or worn cord immediately. 5. Protect the power cable and never allow the cable to come in contact with sharp objects. 6. Do not kink power cable and never allow the cable to come in contact with oil, grease, hot surfaces or chemicals. 7. Make certain that the power source conforms to the requirements of your equipment. 8. KEEP AWAY FROM UNIT WHEN IT IS OPERATING. a. there is a high speed blower wheel inside the blower housing that can amputate fingers, grab loose clothes or neck ties. b. there is also a high speed cooling fan wheel on the top of the motor that should be avoided for the same reasons mentioned in item (a). 9. This unit is heavier than the container it sits on and can be turned over if bumped or not placed on a clean, level area. 10. Do not attempt to clean or service without disconnecting from power source. INTRODUCTION These dust collectors are designed to help maintain clean, safe conditions around dust creating machines in workshops and factories. The flexible hose included with each unit can be hooked directly into the dust creating machine. Dust collectors work by moving larger volumes of air at lower suction pressures than vacuum cleaners. These units are not designed to be used as high-suction vacuum cleaners. Components that must be assembled before operation are: sheet metal cylinder, suction hose, two adjustable clamps, sealing gasket, deflector elbow, discharge guard bag, elbow and the dust bag. See assembly instructions for proper installation. CAUTION: The blower housing contains a high speed radial blade that can amputate fingers, grab loose clothing and neck ties, or propel dust at high velocities. DO NOT OPERATE WITHOUT THE DISCHARGE GUARD BAG, ELBOW AND DUST BAG IN POSITION. Do not attempt to clean, remove dust bag, service unit or move a dust collector while in operation. Disconnect from power source first. UNPACKING Carton must be in upright position before opening. Inspect for shipping damage and advise carrier immediately if damaged. Check parts list for missing or damaged parts. 2 ASSEMBLY 1. Assembly includes the installation of the sheet metal-cylinder, inlet elbows, sealing gasket, discharge gard, bag elbow and dust bag. 2. To install the sheet metal cylinder, inlet elbows and sealing gasket, place the unit upside down on a cardboard covered flat area. 3. The inlet elbow (A) Fig. 2, is to be attached to the bottom of the lid (B). Remove the nuts and washers from the two studs extending out from the bottom of elbow (C). Position inlet elbow (A), as shown, on the two studs and fasten in place using the two washers and nuts. 4. Assemble the sheet metal cylinder (D) Fig. 2, to the bottom of the lid (B) using the three 1/4-20 screws which are installed into nut inserts on bottom of lid. 5. Remove the paper protection from the adhesive side of the sealing gasket (E) Fig. 2, and install the gasket (E) to the underside of the lid next to the rim. The unit will be more effective if there are no air leaks between the lid and the drum. FOR MODELS 50-180 AND 50-181 ONLY 6. After placing the unit right side up on the drum, assemble discharge elbow (F) Fig. 2, to the discharge end of the blower. Slip the 6-inch diameter o-ring (G) against the retaining ring on the open end of discharge elbow (F). 7. Clamp the open end of dust bag (H) Fig. 2, to elbow sleeve (J), using clamp (K) supplied. NOTE: Keep the edge of dust bag fabric 1/4-inch below flange of sleeve (J) to ensure correct locking action of the snap-latches, one of which is shown at (V). With the snap-latches (V) in the raised position, slide the elbow sleeve (J) with the bag attached, over the end of elbow (F) using a slight twisting motion. Snap the l...

Herunterladen

Geben Sie zwei Ziffern: