Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
The wall arm on the CTA-225 is 25.2” in length from the wall mount, providing ample room to install and position a small or large TV/Monitor. CTA-225 Dual Stud Wall Arm BEFORE YOU BEGIN • CAUTION: To prevent damage to your equipment, which could affect or void the Factory warranty, thoroughly study all instructions and illustrations before you begin to install the CTA-225. Pay particular attention to the Warnings and Cautions in this document. • If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-6480. CHIEF MANUFACTURING INC. 8809-000025 (Rev. A) 1-800-582-6480 952-894-6280 FAX 952-894-6918 2004 Chief Manufacturing 8401 EAGLE CREEK PARKWAY, STE. 700 SAVAGE, MINNESOTA 55378 USA Installation Instructions CTA-225 CTA-225 – SPECIFICATIONS (L) Length Table 1. CTA-225 Specifications Max Model L-Length (fixed) Support Weight CTA-225 25.2” 300 lbs (136.1 kg) Installation Instructions CTA-225 IMPORTANT WARNINGS and CAUTIONS! WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions. WARNING Improper installation can result in serious personal injury! Make sure that the mounting surface can support a redundant weight factor five times the total weight of the equipment: if not, reinforce the mounting surface structural members before installing the mount. WARNING Be aware of the potential for personal injury or damage to the equipment if it is not adequately mounted. WARNING The installer is responsible for verifying that the mounting surface to which the CTA-111 is anchored will safely support the combined load of all attached components or other equipment. WARNING The combined weight of the TV/monitor and all attached components and equipment placed on a Chief Wall Arm must not exceed 300 lbs. (136.1 kg), the maximum support weight of the CTA-225. WARNING Watch for pinch points. Do not put your fingers between movable parts. CAUTION Check the unit for shipping damage before you begin the installation. CONTENTS CTA-225 – SPECIFICATIONS........................................2 CONTENTS......................................................................3 INSPECT THE UNIT BEFORE INSTALLING..............3 PARTS ..............................................................................4 TOOLS REQUIRED FOR INSTALLATION..................5 INSTRUCTIONS..............................................................5 Installing Top Stud Spanning Adapter to Wall .............5 Attaching Stud Spanning Adapter to Wall Arm............6 Attaching Wall Arm to Wall-Mounted Top Stud Spanning Adapter..........................................................6 Attaching Bottom Stud Spanning Adapter to Wall.......7 Attaching Front Cover...................................................7 Connecting NPT Pipe or Nipple to Wall Arm...............7 INSPECT THE UNIT BEFORE INSTALLING Unpack the carton. Carefully inspect the parts for shipping damage. Verify contents listed in Table 2. If you are missing any of the listed parts, contact Customer Service at: 1-800/582-6480.300. Table 2. Shipping Contents ITEM DESCRIPTION QTY 10 Wall Arm 1 20 16” Spanning adapter 2 30 Front Cover 1 40 5/16 X 2.5” Lag Bolt 4 50 5/16 Flat Washer 4 60 M8 Flat Washer 6 70 M8 Lock Washer 6 80 M8 Hex Nut 6 90 M4 X 8mm Phillips Head Cap Screw 4 100 M6 X 6mm Set Screw 1 110 M3 Allen Key (not shown) 1 Installation Instructions CTA-225 PARTS 20 10 30 40 70 80 60 90 50 100 Figure 1. CTA-225 Parts Installation Instructions CTA-225 TOOLS REQUIRED FOR INSTALLATION The tools required for installation are as follows: • Electric drill and bit set • Stud sensor (mechanical or electronic) • .” box-end wrench or ratchet with .” socket • 13mm box-end wrench or ratchet with 13mm socket • Level NOTE: Other tools may be required depending on your method of installation. INSTRUCTIONS STEP 1 Installing Top Stud Spanning Adapter to Wall NOTE: The top and bottom stud-spanning adapters must be mounted to wood studs that are 16” apart on center. See Figure 2. 1. Locate the top 16” stud-spanning adapter (20), four lag bolts (40), and four flat washers (50). WARNING It is the installer’s responsibility to verify that the structure to which the mount is anchored will safely support five times the combined load of all attached components and equipment. 2. Determine a suitable mounting location. Keep in mind that both stud-spanning adapters (20) must be mounted to wood studs that are 16” apart on center. 3. Using a stud sensor, locate the two wood studs where you will mount the top stud-spanning adapter (20). 4. Holding the top stud-spanning adapter (20) against the wall, use a pencil, awl, or small nail to mark the mounting holes where two pilot holes will be drilled into the center of the wood studs. Make sure that the mounting...