Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Class IIIa, <5mW, 650 nm Power Supply..................................................................................................................2 AAA, 1.5 Volt Batteries* Battery Life....................................................2.5 Hours Continuous Use — included Alkaline Batteries (Vacuum) 1 Hour Continuous Use — included Alkaline Batteries (Laser) Operating Temperature...................................................................................................................... 32.F to 104.F Dimensions.............................................................................................................. 3-1/2 in. x 2-7/8 in. x 1-3/8 in. Accuracy.......................................................................................................................................± 1/2 in. at 20 ft. * Laser level performance is greatly enhanced when using premium-branded alkaline batteries. KNOW YOUR laser level See Figure 1. The safe use of this product requires an understanding of the information on the tool and in this operator’s manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules. airgrip™ vacuum Technology Your laser level uses a vacuum base that can adhere to smooth surfaces. Using the vacuum seal prevents wall damage caused by nails, pins, or adhesive tape. mounting aid The AIRgrip vacuum may be ineffective on some surfaces. Use the mounting aid to increase the number of surfaces on which the AIRgrip vacuum can be used. assembly UNPACKING This product has been shipped completely assembled. If any parts are damaged or missing, please call 1-800-525-2579 for assistance. operat ion install ing batter ies See Figure 2. n Depress the ridged area on the bottom of the battery cover and pull the cover off the laser level. n Install batteries according to polarity indicators (+ or –) inside the battery compartment. n Place the lens cover back onto the laser level and secure. WARNING: When turning on the laser level, always protect the eyes of yourself and those around you. Never point the laser beam at anyone’s face, including your own. turning on/off See Figure 3. The on/off switch is located on the side of the laser level. Pushing the switch down will turn the laser level on and activate the vacuum pump; pushing the switch up will turn the unit OFF. Always wait for at least 5 seconds between stopping and restarting the laser level. using the airgrip vacuum See Figures 3 - 4. The laser level’s vacuum grip technology allows attachment to most smooth surfaces. n Place the laser level on the surface you want it secured to and push in slightly to seal. n Continue to hold the laser level against the surface while turning on the laser. n Release the laser level slowly when you hear a change in motor sound. NOTE: To release the vacuum seal, turn the laser level’s power off. For fast release, press the protrusion on the side of the unit opposite the power switch. Pulling the laser level off the wall without releasing the vacuum could damage the tool. The laser will automatically shut off 15 minutes prior to battery failure, but the motor will remain on. Press the on/off switch to power down the unit and replace the batteries. operat ing the laser level See Figure 4. n Place the laser level in the area where you want the laser line projected. n Rotate the unit so that the laser lens points in the direction in which you want the line projected. n When a vertical line or level horizontal line is desired, level the tool by centering the bubble inside the appropriate vial located on top of the laser head. n Turn on the laser. using the mounting aid See Figure 4. Using the mounting aid, you can use the laser level’s AIRgrip feature to position the unit on many non-smooth surfaces, including brick, painted cinderblock, textured wallpaper, and stucco walls. NOTE: The AIRgrip feature cannot be used with stucco or unpainted cinderblock. Fig. 2 PACKING LIST Laser Level Mounting Aid AAA Batteries (2) Operator’s Manual WARNING: To avoid serious personal injury, always remove the batteries from the tool when cleaning or performing any maintenance. GENERAL MAINTENANCE n Before initial use, wipe Airgrip vacuum base with a damp cloth to remove any residue. n Store the laser level indoors. n Keep the laser level free of dust and liquids. Use a damp cloth and mild soap to clean the outside casing. Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken, or destroy plastic, which may result in serious personal injury. Fig. 3 maintenance n To clean the laser lens, if needed, use ONLY a soft cloth or cotton swab moistened with glas...