Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
5) to two support brackets using four M8 x 16 hex cap bolts, eight M8 flat washers, and four M8 hex nuts (B, Fig.5). Be sure hose opening faces fan housing. Before attaching third support bracket place the hanger bracket (C, Fig.5) between the support bracket and the housing. Tighten all nuts and bolts at this time with a 13mm wrench. 6. Attach the hose (A, Fig. 6) between the fan housing and the collector housing with two clamps (B, Fig. 6). Tighten the clamps to secure the hose. Fig. 6 10 7. Place the ring over the top of the plastic bag and fold over the bag approximately three inches, Figure 7. 8. Insert the snap ring (A, Fig. 8) of the collector bag into the bottom of the housing at an angle. 9. Pull down on the ring to make sure it “seats” in the housing. Note: make sure the snap ring “snaps” into place in the housing, and also that the plastic bag hangs down approximately 3” so that there are no air leaks. 10. Mount the handle onto the canister filter with two M10 hex nuts, two M10 flat washers, and a M10 lock washer, see Figure 9. 11 Electrical Connections Removing the Collector Bag A WARNING All electrical connections must be done by a qualified electrician. All adjustments or repairs must be done with the dust collector disconnected from the power source, unplugged. Failure to comply may result in _serious injury!_ The DC-1100C dust collector is rated at 115/230V, Prewired 115V. Use a plug and outlet rated at least 20 amps. The circuit for the machine should also be protected by at least a 20 amp circuit breaker or fuse. Keep in mind that a curcuit being used by other machines, tools, lights, heaters, etc. at the same time will add to the electrical load. A dedicated curcuit to the dust collector will give you the best results since dust collectors are generally used at the same time other tools are running. Before hooking up to the power source, make sure that the switch is in the off position. Turning the Machine On & Off Before hooking up to the power source, make sure that the switch is in the off position. The dust collector can be turned on by pressing the start button mounted next to the motor. Press the stop button to turn off the dust collector. Maintenance A WARNING Never perform maintenace on this machine before turning switch off and removing plug from power source, unplug. Failure to comply may cause serious injury! Cleaning the Filter Clean both the filter and collector bag frequently to keep the collector's performance at its optimum. To clean the filter turn the handle a couple rotations so the dust falls into the collector bag. A CAUTION Wearing a particle mask/respirator for protection against fine dust particles during cleaning is highly recommended. 1. Disconnect the machine from the power source, unplug. 2. Remove the collector bag by pushing the ring of the collector bag upwards at an angle and pulling the bag and snap ring out. 3. Empty the contents into an appropriate container. 4. See Page 8 for details on replacing the collector bags. Motor Make frequent inspections of the motor fan and blow out (with low pressure air hose) or vacuum any accumulation of foreign material in order to maintain normal motor ventilation. Connecting the Dust collector to a Machine Use the proper type hose to connect the dust collector to the machine being operated. Dryer vent hose is not acceptable for this purpose. Contact your nearest JET distributor for the full line of JET Dust Collector Hoses and Accessories. Customize your installation and obtain maximum performance with JET's dust hoods, hoses, clamps, fittings, and blast gates. You can also purchase the JET “Dust Collection Basics Video” stock # JW1050V through your JET Distributor Grounding the Dust Collection System The dust collection system includes the dust collector and the hose, or duct work you use to connect the tools. The dust collector is grounded though the ground wire in the cord. The hose or duct work you use to connect the tool to the dust collector must also be grounded. To assist in grounding your system you can purchase the JET “Dust Collector Grounding Kit” stock # JW1053, and also the JET “Dust Collection Basics Video” stock # JW1050V through JET Distributors. 12 Parts Breakdown for DC-1100C Dust Collector w/Canister Filter 13 1.. 2.. 3.. 4.. 5.. 6.. 7.. 8.. 9.. 10 11 12 13 14 15 16 17 18 19 20 21 22 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 1 ■ 1 1 2 2 1 4 1 2 2 1 1 1 3 4 4 4 8 2 4 4 Parts List for the DC-1100C Dust Collector w/Canister Filter Part No. Description Size 708739.........................Filter.............................................................................. 331052.........................Shaft.............................................................................. 331012.........................Scraper.........................................