Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Power use common sense when operating a tools create sparks which may ignite the dust power tool. Do not use tool while tired or or fumes. under the influence of drugs, alcohol, or Keep by-standers, children, and visitors medication. A moment of inattention while away while operating a power tool. operating power tools may result in serious Distractions can cause you to lose control. personal injury. Electrical Safety Dress properly. Do not wear loose clothing Double Insulated tools are equipped with a or jewelry. Contain long hair. Keep your polarized plug (one blade is wider than the hair, clothing, and gloves away from other.) This plug will fit in a polarized outlet moving parts. Loose clothes, jewelry, or long only one way. If the plug does not fit fully in hair can be caught in moving parts. Keep the outlet, reverse the plug. If it still does handles dry, clean and free from oil andnot fit, contact a qualified electrician to grease. install a polarized outlet. Do not change Avoid accidental starting. Be sure switch is the plug in any way. Double Insulation eliminates the need for the three wire “OFF” before plugging in. Carrying tools with grounded power cord and grounded power your finger on the switch or plugging in tools supply system. Before plugging in the tool, be that have the switch “ON” invites accidents. certain the outlet voltage supplied is within the Remove adjusting keys or wrenches before voltage marked on the nameplate. Do not use turning the tool “ON”. A wrench or a key that “AC only” rated tools with a DC power supply. is left attached to a rotating part of the tool Avoid body contact with grounded surfaces may result in personal injury. such as pipes, radiators, ranges and Do not overreach. Keep proper footing and refrigerators. There is an increased risk of balance at all times. Proper footing and electric shock if your body is grounded. If balance enables better control of the tool in operating the power tool in damp locations is unexpected situations. unavoidable, a Ground Fault Circuit Interrupter must be used to supply the power to your Use safety equipment. Always wear eye tool. Electrician’s rubber gloves and footwear protection. Dust mask, non-skid safety will further enhance your personal safety. shoes, hard hat, or hearing protection must be Don't expose power tools to rain or wet used for appropriate conditions. conditions. Water entering a power tool will Tool Use and Care increase the risk of electric shock. Use clamps or other practical way to Do not abuse the cord. Never use the cord secure and support the workpiece to a to carry the tools or pull the plug from an stable platform. Holding the work by hand or outlet. Keep cord away from heat, oil, sharp against your body is unstable and may lead to edges or moving parts. Replace damaged loss of control. cords immediately. Damaged cords increase the risk of electric shock. Do not force tool. Use the correct tool for your application. The correct tool will do the When operating a power tool outside, use job better and safer at the rate for which it is an outdoor extension cord marked "W-A" designed. -2 BM 1619929219 2/03 2/12/03 8:21 AM Page 3 Do not use tool if switch does not turn it caused by poorly maintained tools. Develop a “ON” or “OFF”. Any tool that cannot be periodic maintenance schedule for your tool. controlled with the switch is dangerous and Use only accessories that are recom must be repaired. mended by the manufacturer for your Disconnect the plug from the power source model. Accessories that may be suitable for before making any adjustments, changing one tool, may become hazardous when used accessories, or storing the tool. Such on another tool. preventive safety measures reduce the risk of Service starting the tool accidentally. Tool service must be performed only byStore idle tools out of reach of children and qualified repair personnel. Service or other untrained persons. Tools are maintenance performed by unqualifieddangerous in the hands of untrained users. personnel could result in a risk of injury. For example: internal wires may be misplaced or sharp and clean. Properly maintained tools, Maintain tools with care. Keep cutting tools pinched, safety guard return springs may be with sharp cutting edges are less likely to bind improperly mounted. and are easier to control. Any alteration or When servicing a tool, use only identical modification is a misuse and may result in a replacement parts. Follow instructions in dangerous condition. the Maintenance section of this manual. Use of unauthorized parts or failure to follow Check for misalignment or binding of Maintenance Instructions may create a risk of moving parts, breakage of parts, and any electric shock or injury. Certain cleaning other condition that may affect the tools agents such as gasoline, carbon tetrachloride, operation. If damaged, have the tool ammonia, etc. may damage plastic parts. serviced before using. Many accidents are Rotary Ha...