Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
SAVE THESE INSTRUCTIONS Work Area from an outlet. Keep cord away from Keep your work area clean and well lit. heat, oil, sharp edges or moving parts. Cluttered benches and dark areas invite Replace damaged cords immediately. accidents. Damaged cords increase the risk of electric shock. Do not operate power tools in explosive atmospheres, such as in the presence of When operating a power tool outside, useflammable liquids, gases, or dust. Power an outdoor extension cord marked "W-A" tools create sparks which may ignite the or "W." These cords are rated for outdoor dust or fumes. use and reduce the risk of electric shock. Keep by-standers, children, and visitors Refer to “Recommended sizes of Extension away while operating a power tool. Cords” in the Accessory section of this Distractions can cause you to lose control. manual. Electrical Safety Personal Safety Grounded tools must be plugged into an Stay alert, watch what you are doing andoutlet properly installed and grounded in use common sense when operating aaccordance with all codes and power tool. Do not use tool while tired or ordinances. Never remove the grounding under the influence of drugs, alcohol, or prong or modify the plug in any way. Do medication. A moment of inattention while not use any adaptor plugs. Check with a operating power tools may result in serious qualified electrician if you are in doubt as personal injury. to whether the outlet is properly grounded. If the tools should electrically Dress properly. Do not wear loose malfunction or break down, grounding clothing or jewelry. Contain long hair. provides a low resistance path to carry Keep your hair, clothing, and gloves away electricity away from the user. Improper from moving parts. Loose clothes, jewelry, grounding can shock, burn or electrocute. or long hair can be caught in moving parts. Grounded tools are equipped with three Keep handles dry, clean and free from oilconductor cord and three prong type plugs. and grease. Before plugging in the tool be certain the outlet voltage supplied is within the voltage Avoid accidental starting. Be sure switch marked on the nameplate. Do not use “AC is “OFF” before plugging in. Carrying tools only” rated tools with a DC power supply. with your finger on the switch or plugging in tools that have the switch “ON” invites Avoid body contact with grounded surfaces such as pipes, radiators, ranges accidents. and refrigerators. There is an increased Remove adjusting keys or wrenches risk of electric shock if your body is before turning the tool “ON”. A wrench or grounded. If operating the power tool in a key that is left attached to a rotating part of damp locations is unavoidable, a Ground the tool may result in personal injury. Fault Circuit Interrupter must be used to supply the power to your tool. Electrician’s Do not overreach. Keep proper footing rubber gloves and footwear will further and balance at all times. Proper footing enhance your personal safety. and balance enables better control of the tool in unexpected situations. Don't expose power tools to rain or wet conditions. Water entering a power tool will Use safety equipment. Always wear eye increase the risk of electric shock. protection. Dust mask, non-skid safety Do not abuse the cord. Never use the shoes, hard hat, or hearing protection must cord to carry the tools or pull the plug be used for appropriate conditions. -2 BM 1619929519 12/02 12/10/02 2:52 PM Page 3 Tool Use and Care other condition that may affect the tools Use clamps or other practical way to operation. If damaged, have the tool secure and support the workpiece to a serviced before using. Many accidents are stable platform. Holding the work by hand caused by poorly maintained tools. Develop or against your body is unstable and may a periodic maintenance schedule for your lead to loss of control. tool. Do not force tool. Use the correct tool for Use only accessories that are your application. The correct tool will do recommended by the manufacturer for the job better and safer at the rate for which your model. Accessories that may be it is designed.Do not use tool if switch suitable for one tool, may become does not turn it “ON” or “OFF”. Any tool hazardous when used on another tool. that cannot be controlled with the switch is dangerous and must be repaired. Service Tool service must be performed only by Disconnect the plug from the power qualified repair personnel. Service or source before making any adjustments, maintenance performed by unqualified changing accessories, or storing the tool. personnel could result in a risk of injury. For Such preventive safety measures reduce the example: internal wires may be misplaced or risk of starting the tool accidentally. pinched, safety guard return springs may be Store idle tools out of reach of children improperly mounted. and other untrained persons. Tools are When servicing a tool, use only identical dangerous in the hands of untrained users. replacement parts. Follow i...
Dieses Handbuch ist für folgende Modelle:Andere Werkzeuge - 11240 (1.72 mb)