Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Read and understand this entire document before installation to make sure the Model D3038 fits the intended application. NOTICE This switch is designed to be used only on dust collectors with standard ON/OFF toggle switches. Due to the nature of magnetic switches, the Model D3038 WILL NOT function properly if connected to a machine with this type of switch. If you are uncertain about the type of switch on your dust collector, contact the manufacturer for more information. Do not attempt to bypass the dust collector switch with this unit. Use of the Model D3038 for applications other than dust collectors may cause the unit to fail and will void the warranty. The remote control transmitters and receiver included in this package are programmed specifically for each other. For this reason, replacement transmitters are not available for purchase. If both transmitters are lost or damaged, an entire new unit must be purchased. Only connect the Model D3038 to a 110V circuit with a NEMA 5-15 receptacle. DO NOT connect a dust collec- tor with a motor larger than 11.2 HP. Failure to follow these warnings will void the warranty and could cause damage to the remote switch and the dust collector. Figure 1. Model D3038. Specifications Voltage .............................. 110V Only Max. Current .........................15A Peak Receiver Range ....................... 75 Feet Control Signal .........................Infrared Plug/Receptacle Type.................... 5-15 Inventory (Figure 2) Qty. A. Receiver Unit ............................ 1 B. Remote Control Transmitters.......... 2 C. Tap Screws ............................... 2 D. Mounting Bracket........................ 1 Figure 2. Inventory. A B D C COPYRIGHT © JANUARY, 2011 BY WOODSTOCK INTERNATIONAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. Printed in China #13756JB D3038 Remote Dust Collector Switch Installation 1. Identify a mounting location for the receiver unit that allows the power cord to reach an appropriate outlet and the dust collector power to be plugged into the receiver outlet. Note: You may choose to attach the receiver unit directly to your dust collector. If so, mount it to a portion of the frame that will not compromise the function or strength of the dust collector. 2. Attach the mounting bracket in the chosen location using the included screws, as shown in Figure 3. If you are mounting the bracket to the dust collector frame, you may have to use alternative mounting hardware. 3. Hook the receiver unit onto the mounting bracket. 4. Plug the receiver power cord into a 5-15 receptacle, then plug the dust collector cord into the receiver unit. Only connect the Model D3038 to a 110V circuit with a NEMA 5-15 receptacle. DO NOT connect a dust collec- tor with a motor larger than 11.2 HP. Failure to follow these warnings will void the warranty and could cause damage to the remote switch and the dust collector. Figure 3. Mounting. Wall Mounting Bracket Side View Screws Reciever Unit Grounding Prong Neutral Hot 5-15 PLUG GROUNDED 5-15 RECEPTACLE 110V Figure 4. NEMA 5-15 plug & receptacle. 5. If the batteries are not installed in the remote control transmitters, install them as described on Page 3. DO NOT modify the provided plug or use an adapter if the plug will not fit your receptacle. This is an indication that your power supply circuit does NOT meet the requirements for the machine; have an electrician install the correct power supply circuit. If the machine must be reconnected for use on a different type of electric circuit, the reconnection should be made by a qualified electrician or service personnel; after reconnection, the machine must comply with all local codes and ordinances. -2 D3038 Remote Dust Collector Switch 6. Turn the remote control transmitters ON with the ON/OFF switch shown in Figure 5. The LED Figure 6. Battery installation/ replacement. Figure 5. ON/OFF Switch location. ON/OFF Switch PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Unit will not turn on. 1. Remote is out of range. 2. Signal is obstructed. 3. Remote is not turned ON. 4. Dust collector is turned OFF 5. Receiver circuit breaker has tripped. 6. Wall circuit breaker has tripped. 7. Remote battery is weak/dead. 8. Connected to a machine with a magnetic switch. 9. Dust collector is at fault. 10. Remote control transmitter is at fault. 11. Receiver unit is at fault. 1. Move remote closer to receiver unit. 2. Remove obstructions to provide direct line of sight between remote and receiver. 3. Turn ON remote control transmitter. 4. Turn ON dust collector. 5. Allow unit to cool, then press the button on the bottom of the receiver unit to reset breaker. 6. Reset wall circuit breaker. Check that breaker is in good condition and circuit is properly sized for the dust collector in use. 7. Replace weak/dead battery. 8. Only use this unit on machines with standard ON/ OFFtoggle switches. 9. Re...