Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
You can also log onto the online help section of the Crestron Web site (to ask questions about Crestron products. First-time users will need to establish a user account to fully benefit from all available features. Future Updates As Crestron improves functions, adds new features and extends the capabilities of the GLS-LOL units, additional information may be made available as manual updates. These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision. Check the Crestron Web site periodically for manual update availability and its relevance. Updates are identified as an “Addendum” in the Download column. WARNING: To avoid fire, shock, or death; turn off power at circuit breaker or fuse and test that power is off before wiring! CAUTION: Insufficient power can lead to unpredictable results or damage to the equipment. Please use the Crestron Power Calculator to help calculate how much power is needed for the system (NOTES: Observe the following: • To be installed and/or used in accordance with appropriate electrical codes and regulations. • If you are unsure about any part of these instructions, consult a qualified electrician. • Sensors must be mounted on a vibration free surface. at least 6 feet (1.8 m) away from air vents. Crestron Electronics, Inc. Operations & Installation Guide - DOC. 6774D 15 Volvo Drive Rockleigh, NJ 07647 (2023057) Tel: 888.CRESTRON 08.11 Fax: 201.767.7576 Specifications subject to change without notice. This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc. FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. SETUP Network Wiring When wiring the Cresnet® network, consider the following: • Use Crestron Certified Wire. • Use Crestron power supplies for Crestron equipment. • Provide sufficient power to the system. Preparing and Connecting Wires Strip the ends of the wires approximately 1/2 inch (13 mm). Use care to avoid nicking the conductors. Twist together the ends of the wires that share a connection and tin the twisted connection. Apply solder only to the ends of the twisted wires. Avoid tinning too far up the wires or the end becomes brittle. The label on the rear of the dimmer contains a gauge for wire stripping. Light Level Testing Before installing the photocell, verify the daylight levels on a sunny day at the proposed location of the photocell. With the lights switched off, use a light meter to read the daylight level. Orient the light meter in the same direction the photocell will view. The light levels under sunny conditions must be at least 35 fc. If the light levels are less, you should select another location or reorient the photocell. DESCRIPTION The GLS-LOL is a low voltage photocell which senses light levels and sends this data to an interface device such as the GLS-SIM (sold seperately) connected to the Crestron® control system. Specifications Specifications for the GLS-LOL are listed in the following table. SPECIFICATION DETAILS UL and cUL Listed Class 2 Power Requirements Current Consumption4 mA @ 24 VDC Cresnet Power Usage 1 Watt* Output Signal Range:0 - 10 VDC Light Level Range: Selectable, 3 to 300 footcandles (fc), 30 to 3000 fc, 60 to 6000 fc Recommended Mounting Location Directly above work space Field of View Coverage 60° Cone * Cresnet communications require GLS-SIM Sensor Integration Module (sold separately). Power may be taken from Cresnet bus regardless of interface method. Photocell Placement The photocell is designed for mounting in a dry location that is exposed to daylight. The photocell should not be exposed to direct illumination from an electric light source. The following illustration shows the GLS-LOL field of view. GLS-LOL Field of View and Mounting 2.0 in. (51 mm) Cable to GLS-SIM or other compatible Crestron interface device. 1.2 in. 60. field of view Peak Sensitivity GLS-LOL (31 mm) 45. 30. 30. Ceiling tile or drywall Where windows are the primary source of daylight, the photocell typically mounts on the ceiling between the window and the first row of fixtures. (Refer to the following illustration.) The photocell points toward the window. GLS-LOL Placement 45° GLS-LOL Peak Light Fixture Sensitivity Window For skylight applications, the photocell mounts in the lightwell of the skylight and should be oriented toward the incoming daylight. Typically, the photocell is aimed toward the skylight. The light level range adjustment jumper may need to be changed to 60-6000 fc for skylight applications. INSTALLATION Wiring and Testing NOTE: Use CRESNET-P/-NP cables only. Maximum distance is 250 feet (76 m). 1. To a...