Login:
Stimmen - 3, Durchschnittliche Bewertung: 4.7 ( )

Anleitung Heath Zenith, modell 70 Watt High Pressure Sodium Patio Light 2LBL8

Hersteller: Heath Zenith
Dateigröße: 384.95 kb
Dateiname: 598-1319-02.pdf
Unterrichtssprache:enesfr
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


Complete The Installation 1. Put the Temporary Pin through the holes in the Mounting Bracket. 2. This fixture must be grounded. Connect the supply ground wire to the green ground screw.You can also attach a bare or green “pigtail” to the green ground screw, then connect the ground pigtail to the supply ground when the other supply wires are connected. 3. Slide the fixture onto the Mounting Bracket, and allow the fixture to rest on the Temporary Pin. 4. Connect the fixture wires to the supply wires (black to black, white to white, and if a ground pigtail was added above, connect this pigtail to the supply ground wire). Secure with the wire connectors provided. 5. Remove the Temporary Pin, and slide the fixture all the way down onto the Mounting Bracket making sure no wires get pinched. 6. Install the screw through the bottom of the Mounting Bracket and into the fixture housing. Tighten this screw. 7. Install lamp (provided). Lamp rating must match the rating of the fixture. Model 2LBL7: 50 watt metal halide M110/O open rated lamp. Model 2LBL8: 70 watt high pressure sodium type S62 lamp. 8. Caulk fixture mounting surface with silicone weather sealant. To test operation during daylight, cover the photocontrol with black tape.Turn on the power.The light will take up to ten minutes to reach full brightness. Remove the tape from the photocontrol and your unit will operate automatically—on at dusk, off at dawn. Photocontrol Gasket (Optional) Mounting Bracket Ground Screw Fixture Lamp Temporary Pin HEA 012 Printed in China 598-1319-02 LPG-5659, LPG-5679 Ballast Assembly Replacement Instructions Model 2LBL7 Lamp Socket Photocell Socket Ignitor Ballast LargeCoilSmallCoilRed Red Black 120V AC Input Black Black Blue White White WhiteWhiteWhite WhiteWhite 1. Remove plastic cover. 2. Remove bulb. 3. Remove five screws attaching reflector to fixture housing. 4. Label wires according to wiring diagram. 5. Remove wire nuts from wires. Retain wire nuts to connect replacement ballast assembly. 6. Remove two screws and lock washers holding ballast in place. 7. Dispose of used ballast assembly. 8. Connect the replacement ballast assembly following steps 1 through 6 in reverse order. Ballast assembly can be replaced without the cutting of any wires. Use of a qualified electrician is recommended. WARNING: Turn power off at the fuse or circuit breaker. Fixture Housing Ballast Ballast Retention Screw Lock Washer Reflector Reflector Screw (x5) Ballast Retention Bracket 2 598-1319-02 Ballast Assembly Replacement Instructions Model 2LBL8 Ballast assembly can be replaced without the cutting of any wires. Use of a qualified electrician is recommended. WARNING: Turn power off at the fuse or circuit breaker. 1. Remove plastic cover. 2. Remove bulb. 3. Remove five screws attaching reflector to fixture housing. 4. Label wires according to wiring diagram. 5. Remove wire nuts from wires. Retain wire nuts to connect replacement ballast assembly. 6. Remove two screws and lock washers holding ignitor and ballast in place. CAUTION: Ballast is held in place by ignitor. Carefully remove the ignitor and the ballast together to avoid personal injury in case the ballast slides out of unit. 7. Dispose of used ballast...

Dieses Handbuch ist für folgende Modelle:
Andere Home Zubehör - 50 Watt Metal Halide Patio Light 2LBL7 (384.95 kb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien