Stimmen - 4, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
To help us assist you, please note the product model number and serial number before calling. The model number is IMHS40090. The serial number can be found on a decal attached to the frame inside the spa (see the front cover of this manual). Before reading further, please familiarize yourself with the parts that are labeled in the drawing below. Wood Panels Suction Vents Locking Buckle Access Cover Console Power Cord with Ground Fault Circuit Interrupter (GFCI) Spa Shell Filter Jets 6 Choosing a Location for the Hydrotherapy Spa There are many factors to consider when choosing a location to set up the hydrotherapy spa. These factors vary depending on whether you use the hydrotherapy spa inside or outside. We have listed several factors you may wish to consider as you decide where you want to use the hydrotherapy spa. If you set up the hydrotherapy spa inside: 1. The hydrotherapy spa will increase the level of humidity in your home. The location you choose should be well ventilated. You may need to install a ventilation fan or use a dehumidifier. 2. The location must be close to an electrical outlet. Do not use an extension cord with the hydrotherapy spa. 3. The hydrotherapy spa should be close to a source of water. 4. Do not use the hydrotherapy spa on carpet or other material that may be damaged by moisture. We recommend that you place the hydrotherapy spa on a water- and stain-resistant, non-slip surface with a floor drain for any water that may splash from the hydrotherapy spa. 5. Be sure that the location you choose is stable. It must be able to support the weight of the hydrotherapy spa when it is filled with water, plus the weight of the occupants. The hydrotherapy spa weighs approximately 1800 pounds when filled with water. 6. Do not use the hydrotherapy spa above a finished living area, due to the risk of water damage. 7. Be sure that there is room around the hydrotherapy spa to permit servicing of the unit. The dimensions of the spa are 70OW x 70OL x 29OH. You should allow for this size when choosing the location. 8. The hydrotherapy spa is not designed for in-floor installation. However, it is compatible with a deck system that is built flush with the top of the spa, provided you leave access to the motor for service. 9. Be sure to note any other considerations, such as aesthetics or privacy concerns, that may affect the safety or enjoyment of using the hydrotherapy spa. If you set up the hydrotherapy spa outside: 1. You should check your local building codes concerning the use of outdoor spas. 2. The location must be close to an electrical outlet. Do not use an extension cord with the hydrotherapy spa. 3. The hydrotherapy spa should be close to a source of water. 4. We recommend that you place the hydrotherapy spa on a water- and stain-resistant, non-slip surface. Do not use the hydrotherapy spa on rough or sharp surfaces such as gravel or wood chips. 5. Be sure that the location you choose is stable. It must be able to support the weight of the hydrotherapy spa when it is filled with water, plus the weight of the occupants. The hydrotherapy spa weighs approximately 1800 pounds when filled with water. 6. Think about environmental factors, such as rain, wind, shade, sunlight etc. 7. You should be able to monitor the use of the hydrotherapy spa from your home, to prevent unauthorized use by children. You may want to enclose the spa with a fence and self-latching gate to prevent unauthorized use. 8. Be sure that there is room around the hydrotherapy spa to permit servicing of the unit. The dimensions of the spa are 70OW x 70OL x 29OH. You should allow for this size when choosing the location. 9. The hydrotherapy spa is not designed to be installed below ground level. However, it is compatible with a deck system that is built flush with the top of the spa, provided you leave access to the motor for service. 10.Be sure to note any other considerations, such as aesthetics or privacy concerns, which may affect the safety or enjoyment of using the hydrotherapy spa. 7 Assembly Before beginning assembly, carefully read the following information and instructions: • Place all parts in a cleared area and remove the packing materials from the spa shell. Do not dispose of the packing materials until assembly is completed and the spa is in operation. • During assembly, make sure that all parts are oriented as shown in the drawings. • Read each assembly step before you begin. • Tighten all parts as you assemble them, unless instructed to do otherwise. This unit is a cord-connected spa with pump, heater and spa side controls. 1. Before beginning assembly, make sure that you have read and understand the information in the box above and on the previous two pages. Remove the four #6 x 1 1/4O Wood Screws (7) from the Access Cover (2). Remove the Access Cover from the spa unit by sliding it down and pulling the bottom of the Cover away from the spa unit. Make sure you donOt damage the spa shell. Remove the power cord w...