Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Should any other connections be required they must be carried out with the following configuration. Earth = Green/Yellow cable Neutral = Blue cable Live = Brown cable In the USA & Europe, it is required that all plugs are 3-pin type i.e. with Earth/Ground connection. In the UK, it is required that all mains plugs are fitted with 5A fuses. Technical Specifications Power 120V~60Hz AC 230V~50Hz AC Fuse 20mm Glass 8A Fast Blow 20mm Glass 4A Fast Blow Preheat Time 4 minutes Fog Output 3,500 cu ft per minute Tank Capacity 1 Liter / Quart Dimensions 290 x 178 x 178mm / 11.4in x 7in x 7in Weight 2.1kg / 4.5lbs This product is ETL listed for Canada and the US. Precision Fogger FX-800 Users Guide Please read these instructions carefully before use User Information (Please complete for your records) Date Purchased: // Serial No: Dealer Stamp: Model: FX-800 PRECISION FOGGER World-wide Headquarters: 3000 North 29th Ct., Hollywood Florida, USA, FL 33020 Tel: +1-954-929-1115 Fax: +1-954-929-5560 Fluid Tank Cap Mounting Bracket Nozzle Fluid Tank Cap Mounting Bracket Nozzle At the Rear: . Screw Cap Fuseholder . On/Off Switch . Remote Control Socket . Ready to Fog Light . Fog Button Fig.1 Cleaning Cleaning your fog machine regularly will help reduce costly parts replacement and repair charges. After every 40 hours of continuous operation or when the machine will be idle for a long time it is recommended to run a cleaning solution composed of 80% distilled water and 20% white vinegar through the system to prevent the accumulation of particles in the heating element. 1. While unit is unplugged and cool, unscrew nozzle at very front of unit (fig.1) and clean out debris with white vinegar and a pipe cleaner, making sure that the hole is free and unobstructed. 2. Empty all fog fluid from the machine and replace with cleaning solution in the tank. Plug unit 3. Run unit in a well ventilated area until tank is empty. 4. Replace nozzle. 5. Cleaning is now complete. Unplug and refill with a quality water based fog fluid once cool. Introduction Congratulations on the purchase of your new CHAUVET fog machine. We are confident you will enjoy many trouble free hours with this unit. To assist with the care and use of the product we have prepared this short guide. Operation Before connecting this unit to the mains power supply for the first time you must first fill the fluid tank with fog fluid and check that the nozzle is clean and unobstructed. This fog machine has been designed to function on a mains power supply of either 120V~60Hz or 230V~50Hz and has been fitted with a suitable power plug for use with your local voltage. Check the label on the unit and the power plug for the correct voltage. Place the machine on a level surface and loosen the cap of the fluid tank to fill with quality water based fog fluid. We recommend use of CHAUVET fog fluid as it has been specially formulated for use with CHAUVET foggers. Plug the remote control unit into the socket at the rear and switch on to allow time to preheat. Once the machine has reached temperature and is ready to operate the orange light on the back of the unit and the remote control will illuminate. Push the button on either the rear of the unit or the remote control when lit and hold for prolonged bursts of fog. Always monitor fog fluid level as running the machine with no fluid could cause permanent damage. Please do not touch or place anything in close proximity to the nozzle during operation or preheat as there is a danger of burns. It is normal for your fogger to have a recycling period after long bursts when the unit will shut itself down for a short period in order to heat up to temperature. During this time no fog can be produced. The orange light on the back of the unit and the remote will illuminate when the unit is ready for action again. Due to the high operating temperature of fog machines it is advised that the effect be used in well ventilated areas taking care not to obstruct the air vents. After use, allow time to ‘cool’ for safety before moving or touching. Installation / Mounting The fogger must be used in a horizontal position sitting on a level surface and it may also be mounted using the bracket provided. Avoid fogging directly onto the face of patrons. What ever method of installation you choose; the fogger must not have more than a 15 degree angle of inclination. We always suggest that for safety purposes use of a suitable hanging clamp and safety cable is essential. CHAUVET offers a range of items, which are ideal for safe mounting. All fog machines are prone to clogging due to the consistency of fog fluid and the high temperatures at which it vaporizes. However a well maintained machine should provide years of reliable use. The body of the unit may be cleaned with a dry cloth. Store dry. Maintenance & Servicing Do not allow fog fluid to become contaminated. Always replace cap after use. Work on internal parts should be carried out by a q...