Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
3. Use the Mounting Bracket and a pencil to mark the location of the three holes to be drilled on the bottom of the cabinet. Use a hammer and nail (or center punch) to tap in starter holes at your pencil marks. 4 (Cover) Cover Figure D Figure E Start Release CAUTION: It is strongly recommended that you wear suitable eye protection such as goggles to prevent injury from shavings when using a drill. 4. With a 1/4”(6mm) drill bit, drill straight up through the bottom of the cabinet at your starter holes. Sandpaper or file splinters or rough edges on cabinets. 5. Slip the washers onto the screws so that they rest on the cabinet interior . (Figure C) 6. Hold the Mounting Bracket up to the underside of the cabinet and thread the screws into the holes on the Mounting Bracket. Tighten them with a screwdriver. 7. Slip the cord out through the opening on the back of the Mounting Bracket. (Figure D) 8. Push the can opener onto the Bracket and slide it toward the wall until it snaps into place. (Figure E) Because the can opener fits tightly, you may have to shimmy it back and forth and put pressure at the top as you push it onto the Bracket. 9. Extend the Power Cord to a suitable polarized or adapted electrical outlet. You may store extra cord length by pushing it into the hood of the Bracket or by using the Cord Hook To use the Cord Hook, peel off the paper to expose the adhesive back and place the Hook at the back edge of the cabinet or on a back wall. NOTE: For safety, NEVER PUT TACKS THROUGH OR AGAINST THE CORD. Start Release Locating Tab Start Release Figure F Figure G TO OPEN A CAN 1. Position the can so that the Locating Tab is resting on the rim. (Figure F) 2. Press the Operating Switch down to START and let go of the can as it starts to turn. This is a “hands free” can opener so it is not necessary to hold the Operating Switch or the can during the cutting action. You may want to support tall or large cans over 2 lbs. (0.9 kg). 3. The Retractable Magnet will automatically come down and grab the lid and the can opener will shut off automatically once the lid is cut. Hold down the Operating Switch if the lid is not completely cut. 5 (Cover) Cover Start Release Start Release Figure H Start Release Figure I Start Release Figure J Start Release 4. To avoid dripping or splatter, pull the cut lid out before removing the can. (Figure G) 5. To remove an opened can, hold it with one hand and push the Operating Switch up with the other. (Figure H) The Retractable Magnet will lift automatically. CAN OPENING TIPS ¦ If there is a bump or dent in the rim of the can, open the other end or start cutting just beyond the dent. ¦ Cans with heavy seams, uneven rims, or odd shapes may stall the Can Opener. Turn the can slightly by hand to help the cutting action. NOTE: If the Cutting Blade needs to be replaced, the Can Opener must be returned to a Black & Decker Inc., Household Appliance Company- Owned or Authorized Service Center. A list of the Company-Owned Service Centers can be found on the insert included with this book. TO OPEN BOTTLES 1. The bottle opener is located at the bottom of the unit and requires a side-to-side motion. Use it to remove metal bottle caps only. 2. To open a bottle, grasp it and position the cap under the metal “hook” in the bottle opener. Pull sideways to the right. (Figure I) “ IMPORTANT: Be sure the “hook” is not under the bottle neck or the glass may break. TO OPEN BAGS 1. The bag opener is located at the right side of the Mounting Bracket: 2. To open a bag, grasp it with both hands and pull the top of the bag from back to front through the slot on the Bracket. (Figure J) CAUTION: If the plastic guide over the cutting slot breaks off, the blade inside will be exposed causing a cutting hazard. If that occurs, or if the blade becomes dull, remove the Mounting Bracket and bring or send it to a Black & Decker , Household Appliance Company Owned or Authorized Service Center. Figure K (Cover) Cover 6 CLEANING YOUR CAN OPENER 1. Unplug the can opener. 2. Press down on the Blade Release Lever to pop the Cutting Assembly loose. Remove it carefully. You may wash it in hot, sudsy water or a dishwasher. (Figure K) 3. Dry the Cutting Assembly thoroughly before replacing it. Insert the pin on the Assembly into the opening. If necessary, twist the Assembly back and forth until it is “seated”, then push it in. 4. The body of the can opener and other stationary parts can be cleaned with a damp cloth. The entire unit may be removed from the Mounting Bracket for more thorough cleaning. SERVICE OR REPAIR Service, if necessary, must be performed by a Black & Decker, Household Appliance Company-Owned or Authorized Service Center. The Service Center nearest you can be found in the yellow pages of your phone book under “Appliances-Small-Repairing.” For your convenience, a complete listing of our Company-Owned Service Centers can be found on the insert sheet included with this book. If mailing or shipping your Can Opener, r...