Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Note that some functions require the use of the K-4 keypad (10 keys). * Starting Pump 1: Turning the light on: Press Pump 1 to turn Pump 1 on at low speed. Press a second time to turn Pump 1 to high speed. A third time turns Pump 1 off. A built-in timer automatically turns pump off after 20 minutes, unless it has been manually deactivated. The "Pump 1" indicator lights up when Pump 1 is on at high speed. It flashes when Pump 1 is on at low speed. Starting Pump 2: Dual-speed pump system: Press Pump 2 to turn Pump 2 on at low speed. Press a second time to turn pump to high speed. A third time turns pump off. Single-speed pump system: Press Pump 2 to turn Pump 2 on. Press a second time to turn Pump 2 off. In both cases, a built-in timer turns Pump 2 off after 20 minutes, unless it has been manually deactivated. The "Pump 2" indicator lights up when Pump 2 is on. With a dual-speed pump, it will flash when Pump 2 is on at low speed. Starting the blower: Press Blower to turn blower on at high speed. Press a second time to turn blower to low speed. A third time turns blower off. A built-in timer automatically turns blower off after 20 minutes, unless manually deactivated first. The "Blower" indicator lights up when blower is on at high speed. It flashes when blower is on at low speed. Automatic water heater start: When water temperature is 0.5.C (1.F) lower than the Set Point, the heater will automatically turn on until water temperature reaches Set Point plus 0.5.C (1.F). The "Heater" indicator lights up when the heater is on. It flashes when there is a request for more heat but the heater has not yet started. Note: The heater will not start if two pumps or more are running at high speed. Setting water temperature: Use Up or Down arrow key to regulate water temperature. The temperature setting will be displayed for 5 seconds to confirm your new selection. The "Set Point" symbol indicates the desired temperature, NOT the current water temperature! Water temperature can be adjusted by 0.5.C or 1.F increments from 15 to 40.C (59 to 104.F). Two-intensity spa light: To advance to the next color/display setting, press Press Light key to turn light on at high intensity. Light key twice. The LEDs will go off with the first Press a second time to turn light to low inten-press, then back on in the next setting with the sity. A third time turns light off. second press. If the LEDs remain off for more than 5 sec., the color/ display sequence will reset One-intensity spa light: and start back at the beginning the next time the Press Light key to turn light on. Light key is pressed. Color/ display sequences are: Press a second time to turn light off. 1• LEDs light up and slowly cycle through all In both cases, a built-in timer turns light off after six colors. The slow cycle restarts at the 2 hours, unless manually deactivated first. beginning and repeats. light up and remain on in Aqua. light up and remain on in Purple. light up and remain on in Blue. light up and remain on in Gold. light up and remain on in Green. light up and remain on in Red. light up for 2 sec., flash off, then ash on in the next color until all six colors have been displayed. The flashing cycle then repeats itself. 9• LEDs flash on/off quickly for a strobe light effect. A built-in timer turns lights off after 2 hours unless manually deactivated first. The "Light" icon is displayed when LED light is on. Standby mode: The "Light" indicator is displayed when light is on at high intensity. It flashes when light is on at low intensity. Fiber Box Option: If your spa has an optional fiber box, press Light key to turn fiber box (motor & light) on. Press a second time to turn fiber box motor off and leave light on. A third time turns both motor and light off. A built-in timer turns fiber box off after 2 hours, unless it has been manually deactivated. The "Light" indicator is displayed when fiber box light is on. It flashes when fiber box motor and light are on at the same time. LED Light Option: If spa has an optional LED 2• LEDs 3• LEDs 4• LEDs 5• LEDs 6• LEDs 7• LEDs 8• LEDs fl light, Press Light key to turn LED lights on. Press and hold Filter key for 5 seconds to turn Starting Pump 3: * the system down (i.e. to set it to Standby mode) for 60 minutes. The display toggles Press Pump 3/Off to turn Pump 3 on. Press between "SBY" message and the time re- a second time to turn Pump 3 off. A built-in maining. All keys are then disabled, unless timer automatically turns pump off after you press Filter key to reactivate the system 20 minutes, unless manually deactivated first. before the expiration of the 60-minute delay. Troubleshooting Pumps have started up for one minute on several occasions and "Filter Cycle" icon is flashing. Not a bug but a feature! Our Smart Winter Mode Water temperature is displayed. Water temperature in the spa has reached 44.C (112.F). Do not enter the water! 3 flashing dots are displayed. A problem has been detected. Do not enter the water!...