Stimmen - 5, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
4. Do not use the hydrotherapy spa on carpet or other material that may be damaged by moisture. We recommend that you place the hydrotherapy spa on a water- and stain-resistant, non-slip surface with a floor drain for any water that may splash from the hydrotherapy spa. 5. Be sure that the location you choose is stable. It must be able to support the weight of the hydrotherapy spa when it is filled with water, plus the weight of the occupants. The hydrotherapy spa weighs approximately 2000 pounds when filled with water. 6. Do not use the hydrotherapy spa above a finished living area, due to the risk of water damage. 7. Be sure that there is room around the hydrotherapy spa to permit servicing of the unit. The dimensions of the spa are: 5O10OW x 6O4OL x 2O6OH. You should allow for this size when choosing the location. 8. The hydrotherapy spa is not designed for in-floor installation. However, it is compatible with a deck system that is built flush with the top of the spa, provided you leave access to the motor for service. 9. Be sure to note any other considerations, such as aesthetics or privacy concerns, which may affect the safety or enjoyment of using the hydrotherapy spa. If you set up the hydrotherapy spa outside: 1. You should check your local building codes concerning the use of outdoor spas. 2. The location must be close to an electrical outlet. Do not use an extension cord with the hydrotherapy spa. 3. The hydrotherapy spa should be close to a source of water. 4. We recommend that you place the hydrotherapy spa on a water- and stain-resistant, non-slip surface. Do not use the hydrotherapy spa on rough or sharp surfaces such as gravel or wood chips. 5. Be sure that the location you choose is stable. It must be able to support the weight of the hydrotherapy spa when it is filled with water, plus the weight of the occupants. The hydrotherapy spa weighs approximately 2000 pounds when filled with water. 6. Think about environmental factors, such as rain, wind, shade, sunlight, and so forth. 7. You should be able to monitor the use of the hydrotherapy spa from your home, to prevent unauthorized use by children. You may want to enclose the spa with a fence and self-latching gate to prevent unauthorized use. 8. Be sure that there is room around the hydrotherapy spa to permit servicing of the unit. The dimensions of the spa are: 5O10OW x 6O4OL x 2O6OH. You should allow for this size when choosing the location. 9. The hydrotherapy spa is not designed for inground installation. However, it is compatible with a deck system that is built flush with the top of the spa, provided you leave access to the motor for service. 10. Be sure to note any other considerations, such as aesthetics or privacy concerns, which may affect the safety or enjoyment of using the hydrotherapy spa. 7 SET-UP AND ASSEMBLY Before beginning assembly, carefully read the . Read each assembly step before you begin. following information and instructions: . Tighten all parts as you assemble them, unless • Place all parts in a cleared area and remove the instructed to do otherwise. packing materials from the spa shell; do not dispose of the packing materials until assembly is ASSEMBLY REQUIRES THE FOLLOWING completed and the spa is in operation. TOOLS (not included): . Assembly requires two people. . One (1) phillips screwdriver • During assembly, make sure that all parts are ori-. You may also need some soap or wax. ented as shown in the drawings. 1. Before beginning assembly, be sure that you have read and understand the information on the previous two pages. Remove the four cover screws from the access cover. Remove the access cover from the Spa Unit (15) by sliding the access cover down and pulling the bottom of access cover away from the Spa Unit. Be careful not to damage the spa shell. Remove the Power Cord with the GFCI (38) from inside the Spa Unit (15). 2. Locate and check the position of the cut-off valves. Occasionally the valves will be closed at the factory during manufacturing. The cut-off valves must be open for proper spa operation. To open the valves, hold one of the handles and turn the handle until you can pull it out to the open position. Open the other valve in the same manner. WARNING: THE MOTOR WILL BE DAMAGED IF IT IS OPERATED WITH THE CUT-OFF VALVES CLOSED. Close the valve knob on the drain hose. Thread the cap onto the drain hose. Thread the drain plug into the Pump Motor (13). Tighten the pump fittings. 1 Access Cover Access Cover Screws Spa Shell 15 38 2 Cut-off Valve Pump Fittings Cut-off Valve Drain Hose Valve KnobCap 13 Drain Plug 8 3. Wipe out the spa shell using a damp cloth. Remove the two warning decals (not shown) from the spa shell. Before you fill the spa, be sure that it is in the position you want, and that it can be easily serviced, if needed. Once the spa is filled with water, it must be drained to be moved. Using a garden hose or other clean water source, begin filling the spa. Do not use soft water. T...
Dieses Handbuch ist für folgende Modelle:Andere Home Zubehör - Daybreak 515 WLHS42080 (2.6 mb)