Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Desa Tech Dateigröße: 360.93 kb Dateiname: Unterrichtssprache:

If so, repeat steps 1 through 7. WARNING: Keep face and hands away from burner area. 7. When burner lights, keep control valve button pushed in. Release but- ton after 30 seconds. Note:If heater fails to ignite within 10 seconds, gas supply line may have air in it. If so, repeat steps 1 through 7. 8. To shut off appliance, push shutoff switch into the OFF position. Shutoff Switch Ignitor Button Gas Control Valve Button FOR YOUR SAFETY READ BEFORE LIGHTING• Immediately call your gas supplier BATTERY CHECK hear anything, see Battery Check, this WARNING: Close equipment shutoff valve when appliance is not in use. The electronic spark ignitor operates on one alkaline AA battery (not included). The battery is located within the ignitor module behind the ignitor button. See WARNING: Do not hold match. Lay burning match on top of lava rock. 6. Push in and hold control valve button. WARNING: Keep face and hands away from burner area. 7. When burner lights, release the igni- tor button. Keep control valve but- ton pushed in. Release button after 30 seconds. Note:If heater fails to ignite within 10 seconds, gas supply line may have air in it. If so, repeat steps 1 through 7. WARNING: Keep face and hands away from burner area. 7. When burner lights, keep control valve button pushed in. Release but- ton after 30 seconds. Note:If heater fails to ignite within 10 seconds, gas supply line may have air in it. If so, repeat steps 1 through 7. 8. To shut off appliance, push shutoff switch into the OFF position. Shutoff Switch Ignitor Button Gas Control Valve Button OWNER’S MANUAL OPERATING APPLIANCE WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury, or loss of life. WARNING: Do not use this appliance if any gas control parts have been under water. Immediately call a qualified service person to inspect the Patio Fire and replace any part of the control system and any gas control that has been under water. from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. LIGHTING INSTRUCTIONS Lighting Using the Electronic Spark Ignition System 1. Open equipment shutoff valve. 2. If you smell gas, STOP! Turn the equipment shutoff valve to OFF. Check gas connections for leaks. Do not continue until gas leaks are corrected. 3. After correcting leaks, wait five (5) minutes to clear out any gas. If you then smell gas, STOP! Follow the safety information in column 1. If you do not smell gas, go back to step 1. 4. Make sure shutoff switch on control panel is in the ON position (see Figure 6). 5. Push in and hold the electronic spark ignitor button. Note:You should be able to hear a rapid clicking sound from the burner bowl when the ignitor button is depressed. If you do not Figure 7 - Shutoff Switch, Ignitor Button, and Gas Control Valve Button 8. To shut off appliance, push shutoff switch to the OFF position. Battery Installation, page 6, for replacement instructions. 7 For more information, visit NATURAL GAS DECORATIVE PATIO FIRE TROUBLESHOOTING Note: For additional help, visit DESA International’s technical service web site at Note: All troubleshooting items are listed in order of operation. OBSERVED PROBLEM When ignitor button is pressed, there is no spark at burner WARNING: Turn off appliance and let cool before servicing. Only a qualified service person should service and repair appliance. POSSIBLE CAUSE 1. Ignitor electrode not connected to ignitor cable 2. Ignitor cable pinched or wet 3. Broken ignitor cable 4. Bad electronic ignitor 5. Ignitor electrode broken 6. Ignitor electrode positioned wrong 7. Batteries dead or missing 8. Ground wire not attached REMEDY 1. Reconnect ignitor cable 2. Free ignitor cable if pinched by any metal or tubing. Keep ignitor cable dry 3. Replace ignitor cable 4. Replace electronic ignitor 5. Replace electrode 6. Reposition electrode 7. Replace batteries 8. Reattach ground wire to ignitor When ignitor button is pressed, there is 1. Gas supply turned off or equipment 1. Turn on gas supply or open equipment spark at burner but no ignition shutoff valve closed shutoff valve 2. Control knob not pressed in 2. Press in control knob while lighting 3. Air in gas lines when installed 3. Continue holding down control knob. Repeat igniting operation until air is removed 4. Low gas pressure 4. Check for proper supply pressure Burner lights but flame goes out when con1. Control knob not fully pressed in 1. Press in control knob fully trol knob is released 2. Control knob not pressed in long enough 2. After burner lights, keep control knob pressed in 30 seconds 3. Shutoff switch not in ON position 3. Turn switch to ON position 4. Equipment shutoff valve not fully open 4. Fully open equipment shutoff valve 5. Burner flame not touching thermo5. A) Contact local natural gas company couple, which allows thermocouple to cool, causing bu...

Herunterladen

Geben Sie zwei Ziffern: