Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-- please read these instructions carefully before you begin. Certified to comply with ANSI A112.18.1 CARTRIDGE ADAPTOR AND MTG. SCREWS ESCUTCHEON SCREWS ESCUTCHEON METAL LEVER HANDLE CAP SET SCREW SHOWER FLANGE SHOWER ARM DIVERTER SPOUT HANDLE BUSHING CARTRIDGE SEALS HOT LIMIT STOP CARTRIDGE SCREW VALVE BODY WITH STOPS TM PRESSURE BALANCING UNIT U.S. Patent No. D400,652 1/2" SWEAT PLUG 1/2" NPT PLUG VALVE BODY FINISHED WALL 4" TOP OF TUB RIM BOTTOM OF TUB 74" FOR HEAD CLEARANCE 4" REF. 1-5/8" TO 3-1/4" 18" OPTIONAL 5-1/8" REF. 1/2" I.P.S. 1/2" COPPER OR1/2" NPT 7-5/8" 1" MIN. 5-1/2" REF. BATH 1/2" NPT OPTIONAL TO FINISHED FLOOR USUALLY BETWEEN 65'' AND 78'' "SEE ILLUSTRATION BELOW" INLETS 4-1/16" 4-1/16" INLETS 1/2" NOM. COPPER SWEAT SHR. 1/2" NOM. COPPER SWEAT TUB 1/2" NOM. COPPER SWEAT 2" SWEAT INLETS THREADED INLETS INLETS 3-3/8" INLETS 1/2" NPT 3-3/8" SHR. 1/2" NPT TUB PORT 1/2" NPT ROUGHING-IN DIMENSIONS To assure proper positioning in relation to wall, note roughing-in dimensions. INLETS 1/2" NOM. COPPER SWEAT SHR. 1/2" NOM. COPPER SWEAT TUB 1/2" NOM. COPPER SWEAT SWEAT INLETS (STOPS) THREADED INLETS (STOPS) 4-1/16" 5-7/8" SHR. 5-7/8" 1/2" NPT TUB PORT 1/2" NPT' INLETS 1/2" NPT 3-3/8" For toll-free information and answers to your questions, call: 1-800-442-1902 Weekdays 8:00 a.m. to 6:00 p.m. EST IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) Weekdays 8:00 a.m. to 7:00 p.m. EST IN MEXICO 01-800-839-12-00 P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c . © AS America, Inc. 2008 HOT LINE FOR HELP INSTALL TRIM 1 2 CARTRIDGE STEM ADJUSTMENT WHEN WATER IS TOO HOT ADJUSTMENT WHEN WATER IS TOO COLD PRY FORWARD TO UNLOCK AND ROTATE COUNTERCLOCKWISE ONE CLICK PRY FORWARD TO UNLOCK AND ROTATE CLOCKWISE "A" "B" By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP reduces risk of accidental scalding. To set the maximum hot water temperature of your SEVA faucets, all you need to do adjust the setting on the HOT LIMIT SAFETY STOP. Remove HANDLE, CAP and HOT LIMIT STOP. Follow "A" or "B" to adjust maximum discharge temperature. 3 HOT LIMIT STOP 4 SERVICE When finished, tiling the wall, remove PLASTER GUARD. Push on CAP. Mount ESCUTCHEON with SCREWS. Install HANDLE by pushing it onto CARTRIDGE STEM and tightening SET SCREW from below. Install SHOWER ARM with FLANGE and SHOWER HEAD. Install SPOUT. Check proper operation of HANDLE and DIVERTER SPOUT. SPOUT SHOWER ARM SHOWER HEAD TUB FILLER TUBES* (5/8" O.D. - 1/2" NOMINAL) BODY STEM SCREWS RISER PIPE * BRACE (4) * FLANGE PLASTER GUARD * NOT INCLUDED IN KIT REMOVE BURRS FROM TUBE Turn off water at MAIN supply. To prevent damage temporarily CAUTION remove STOPS when water supply lines are soldered to the manifold. ROUGHING-IN Connect hot and cold water supplies. For support, use pipe BRACES secured to wooden braces. With valve turned off, turn on water supplies and check for leaks. See Roughing-in diagram on reverse side. Connect RISER PIPE to MANIFOLD top outlet marked "SHR". Connect TUB FILLER PIPE at bottom outlet marked "TUB". Supply connections are: 1/2" copper sweat for sweat inlets. 1/2" female NPT for threaded inlets. For proper positioning the finished wall must be within side wall of PLASTER GUARD. If the valve is installed on a fiberglass or other thin wall application, the PLASTER GUARD can be used as a support: Cut a 3" dia. hole in the shower stall. If stops are used drill two additional 1" holes to allow access to the stops. Remove PLASTER GUARD, rotate 180° so that indicated screw holes fit manifold. Push CAP on valve, place ESCUTCHEON and attach with screws. ESCUTCHEON SCREWS ESCUTCHEON METAL LEVER HANDLE CAP SET SCREW HANDLE BUSHING COLD HOT CARTRIDGE Remove HANDLE, CAP, HOT LIMIT STOP and CARTRIDGE. Clean inlets and MANIFOLD. Reassemble CARTRIDGE, alternately tightening screws. Replace HOT LIMIT STOP , CAP and HANDLE. Check flow. If faucet drips, operate handle several times from "off" to "on". Do not apply excessive force. Clogged CARTRIDGE inlets may cause reduced flow in "full on" hot or cold. To clean inlets, first turn off water supply, then: VALVE BODY MANIFOLD CARTRIDGE SEALS CARTRIDGE HOT LIMIT STOP CARTRIDGE MTG. SCREWS PLUG (NPT) PLUG (SWEAT) M968395 Rev. 1.1 When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK STOPS (IF PRESENT). When finished soldering, flush valve body, replace cartridges, check stops (if present) and plaster guard to continue installation. Use thread sealant or Teflon tape on threaded connections NOTE ...