Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
5,819,789 SHOWER HEAD SHOWER ARM UNION SWIVEL COUPLING NUT PLASTER GUARD "COLD" "HOT" RUBBER RING SLEEVE VALVE COVER ESCUTCHEON TRANSFER VALVE (2) 1-13/16" DIA. HOLES FOR VALVES ON 8" CENTERS (1) 1-13/16" DIA. HOLE FOR CENTER TRANSFER VALVE CROSS BRACE FINISHED WALL 1-1/4 DIA HOLE 1-3/4 TO 3-3/8 OPTIONAL TO FINISHED FLOOR USUALLY BETWEEN 65'' AND 78'' 1/2" N.P.T. SHOWER ARM 1-1/2 ROUGHING-IN DIMENSIONS 7 REF. 1-3/4 TYP. 1-3/4 UNION INLET 1/2"-14 N.P.T. 1/2" N.P.T. TO SHOWER 9 REF. 74 FOR HEAD CLEARANCE (OPTIONAL) 48 OPTIONAL to FINISHED FLOOR NOTE: NO CONCEALED PIPING FURNISHED SPOUT 1-1/2" 4" 1/2" N.P.T. MAXWALL MIN1-5/8"DEEP 5" REF. VALVE STREAM STRAIGHTENER HANDLE ADAPTER FINISHED FLOOR TUB RIM THREE HANDLE BATH/SHOWER SETS with EverClean™ Finish Congratulations on purchasing your American Standard faucet with EverClean finish found only on American Standard faucets. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. EverClean Finish • One wipe effortlessly removes spots • Eliminates the need for cleaners and scrubbing • Permanent surface protectant remains beautiful for the life of the faucet • EverClean™ available on: Polished Chrome, Satin Nickel, Stainless Steel, Polished Brass (or any combination of these finishes) Turn off hot and cold water supplies before beginning. CAUTION1CAUTION1 ROUGHING-IN FITTING Prepare water supplies per "Roughing-in Dimensions." Slip COUPLING NUT over supply pipe and screw UNION SWIVEL to pipe. For Sweat Connection: Slip COUPLING NUT over 5/8" O.D. supply tube and solder tube into UNION SWIVEL or female inlet of valve. Install VALVE at indicated height and depth. Notice that finished wall has to be between the MAX WALL and MIN. which is 1-5/8" below. Connect HOT water supply to left VALVE inlet and COLD water supply to right VALVE inlet. Tighten both COUPLING NUTS firmly. Secure VALVE BODY to cross brace of wall structure. STEM SOCKET 2 ROUGHING-IN SHOWER AND SPOUT Prepare SHOWER RISER, ELBOW, and roughing-in NIPPLE and connect to top outlet of VALVE BODY. Outlet is 1/2" female NPT. UNION Prepare TUB FILLER PIPE, ELBOW and 1/2" NPT SPOUT NIPPLE. SWIVEL Final length of SPOUT NIPPLE to be 1-1/2" from finished wall. Add cross braces to wall structure and secure piping. COUPLING NUT Remove PLASTER GUARDS by turning counter clockwise and pulling. (Do not discard). Cap roughing-in nipples, open supply lines and check for leaks. PLASTER GUARD has a STEM SOCKET to operate valves. Turn PLASTER GUARD over and push STEM SOCKET onto VALVE STEM. Open hot and cold valves and check for leaks. Close both valves, turn off water supplies, and replace PLASTER GUARDS. ELBOW ROUGH-IN NIPPLE TUB FILLER PIPE SPOUT CROSS BRACE SUPPLY PIPE "HOT" "COLD" "MAX WALL" PLASTER GUARD ROUGH-IN NIPPLE ELBOW MAXWALL EP MAXWLL EP MAXWLL EP SHOWER ARM SHOWER HEAD Finish wall construction. 3 FINISHING INSTALLATION Remove caps from roughing-in nipples. DEEP ROUGH-IN SHALLOW ROUGH-IN Remove PLASTER GUARD by turning counter-clockwise and pulling. If VALVE BODY is roughed in deep (more than 1-1/2") screw SLEEVE in ESCUTCHEON facing front of ESCUTCHEON. If VALVE BODY is roughed in SHALLOW (less than 1-1/2") screw SLEEVE in ESCUTCHEON facing back of ESCUTCHEON. Assemble RUBBER RING to ESCUTCHEON. Screw ESCUTCHEON and SLEEVE onto VALVE COVER against wall. Install SHOWER ARM, SHOWER ARM FLANGE and TUB SPOUT. 4 TEST INSTALLED FAUCET Turn HANDLES into "off" position. Turn on water supplies and check all connections for leaks. MORE THAN RUBBER RING VALVE COVER LESS THAN 1-1/2" SLEEVE VALVE 1-1/2" SLEEVE BODY ESCUTCHEON Operate both HANDLES to flush water lines thoroughly. Check SHOWER HEAD and connections for leaks. Turn handles into OFF position. 5 SERVICE To change direction of handle rotation, proceed as follows: STOP WASHER Turn valve to OFF position. Pull out INDEX CAP and remove HANDLE SCREW. Pull off HANDLE BASE and remove ADAPTER. Remove SPRING CLIP. Lift STOP WASHER, turn 90.. and replace. Replace SPRING CLIP. Reinstall HANDLE. (See step 4). SPRING 90.. CLIP If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90... IN MEXICO 01-800-839-12-00 M968716 Rev.1.1 Product names listed herein are trademarks of American Standard Inc. ©American Standard Inc. 2000 HOTLINE FOR HELP For toll-free information and answers to your questions, call: 1 (800) 442-1902 Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093) ...