Stimmen - 5, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
water pressure 145 psi Recommended water pressure 14.5 – 72 psi Recommended hot water temp. 120°F – 140°F* *Know and follow all applicable local plumbing codes when setting the temperature on your water heater. Installation Considerations Rough valve 10303181 must be installed. The finished wall must be installed and made watertight before installation of this trim kit. For best function of this unit, the hot and cold supplies must be of equal pressure. This faucet may be used with a continuous flow water heater as long as the flow pressure is at least 14.5 psi. For best results, Hansgrohe recommends that this faucet be installed by a licensed professional plumber. Turn the water off at the main before beginning installation. Installation Remove the covers. Trim the plaster shields so that they extend 1/16” outside the surface of the finished wall Use a 17 mm deep socket wrench to remove the cartridges. Install the new cartridges. The hot cartridge is marked with notches. Seal the wall around the plaster shields with waterproof sealant. Failure to seal the wall can lead to possible water damage. Push the extension spindle over the stem. Cut the extension spindle so that it extends 3/16” outside the surface of the finished wall. Remove the plug from the spout port. Thread the coupling over the stem. Cut the coupling so that it extends .” outside the surface of the finished wall. For the spout: Measure the distance between the rough and the end of the plaster shield Record this measurement (“X”). Add 1 .” to this measurement. Cut the connecting thread so that it is X + 1 .” long. Wrap the threads on the connecting thread with Teflon tape (1). Use an 8 mm Allen wrench to install it in the rough (2). Do not overtighten the connecting thread! (3) Push the baseplate against the wall. Install the handle nuts, color rings, and handle fixing sets. Tighten the screws. The connecting thread should extend 1 1/8” outside the surface of the finished wall. 1 2 3 Push the spout over the connector. Tighten the screw with a 2 mm Allen wrench. Push the handles over the snap connectors. In the off position, the handles should be horizontal. If one of the handles is not horizontal, remove it (1), turn it slightly (2), and reinstall it (3). 2 3 1 User Instructions Pivot the handle up to turn the water on. Pivot it down to turn the water off. In the “off” position, the handle is horizontal. If the flow of water diminishes over time, use the spray former tool to remove the spray former. Flush the spray former with clear water. Replace the spray former. Replacement parts 1 handle 34095XX0 2 color ring set 98927000 3 handle fixing set 98932000 4 nut 98929XX0 5 seal 97530000 6 fixing set 96393000 7 connecting thread 98933000 8 spray former 98926000 9 spout cpl. 225 mm 98935XX0 10 flange 98936000 11 hot cartridge 96350000 12 cold cartridge 96351000 13 spray former tool 98987000 XX = colors 00 = chrome 82 = brushed nickel 11 13 12 7 10 11x2 1 33x1,5 6 5 M4x4 4 2 8 3 9 Cleaning Recommendation for Hansgrohe Products Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning. Cleaning Materials for Faucets and Showers Acids are a necessary ingredient of cleaning materials for removing lime, however please pay attention to the following points when cleaning faucets and showers: Only use cleaning materials which are explicitly intended for this type of application. Never use cleaning materials which contain hydrochloric, formic, phosphoric, or acetic acid, as they cause considerable damage. Never mix one cleaning material with another. Never use cleaning materials or appliances with an abrasive effect, such as unsuitable cleaning powders, sponge pads, or micro fiber cloths. Cleaning Instructions for Faucets and Showers Please follow the cleaning material manufacturer’s instructions. In addition, pay attention to the following points: Clean the faucets and showers as and when required Use the amount of cleaning product and the amount of time recommended by the manufacturer. Do not leave the cleaner on the fixture longer than necessary. Regular cleaning can prevent calcification. When using spray cleaners, spray first onto a soft cloth or sponge. Never spray directly onto the faucet as droplets can enter openings and gaps and cause damage. After cleaning, rinse thoroughly with clean water to remove any cleaner residue. Important Residues of liquid soaps, shampoos, and shower foams can also cause damage, so rinse with clean water after using. Please note: if the surface is already damaged, the effect of cleaning materials will cause further damage. Components with damaged surfaces must be replaced or injury could result. Damage caused by improper treatment is not covered under the warranty. Limited Lifetime Consumer Warranty This product has been m...