Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
The suction vents (A) located near the floor of the spa bring the water into the pump in order to operate the system. The suction covers should always be in place over the suction vents. Never operate the spa without the suction covers in place. The filter (B) can be removed for replacement and cleaning (see CHECKING AND CLEANING THE FILTER on page 13). The temperature probe (C) reads the current water temperature. Use of the console (D) is explained on page 12 of this manual. The hydrotherapy spa offers an automatic freeze protection. If the water temperature falls below 40uF, the pump will begin circulating the water to prevent the water from freezing. SECURING THE SPA COVER The spa cover can be secured by snapping the latches on the spa cover into the buckles on the side panels. The buckles can be locked by inserting the key and turning it clockwise a quarter turn. To unlock the buckles, insert the key and turn it counterclockwise a quarter turn. Latch Key Buckle Always keep the buckles locked when the spa is not in use. Keep the keys in a safe place, out of the reach of children. 11 12 Console Diagram USING THE CONSOLE Refer to the console diagram above. The function of each console control is explained below: Air Control: Determines the amount of air that is in the spa jet system during operation. If the control is turned to the left, the amount of air flowing through the jets will increase. If the control is turned to the right, the amount will decrease. On/Off Button: Turns the spa on and off. When you first press the on/off button, the spa jet unit will run at low speed, providing gentle hydrotherapy. Press the button again and the spa will run at high speed, providing more intense hydrotherapy. Press the button a third time, and the spa will shut off. The spa also features an automatic mode which heats and filters the water when the spa is left unattended. When the spa is first plugged in, or if the buttons on the console have not been used for longer than twenty minutes, the automatic mode will begin filtering or heating the water, as needed. Note: To keep the filter and heat cycles from running, the power cord must be unplugged. Thermostat: Controls the temperature of the water. The water heats at about 1.8.F an hour with the cover on. The thermostat can be set to heat the water from 70.F to 104.F. You should use a medical or other accurate thermometer to check the temperature of the water. Thermostat On/Off Button Air Control Maintenance The hydrotherapy spa is designed to provide you with years of enjoyment. Please follow the guidelines below to properly maintain your hydrotherapy spa. MAINTENANCE SCHEDULE DAILY . Check the water level and refill the spa to the level shown on page 9, step 3. . Check the pH balance and sanitizer level. Adjust if necessary (see WATER CHEMISTRY on page 14). . Clean the surface of the water with a skimming net. WEEKLY . Clean the spa shell at the waterline. . Check and thoroughly clean the filter (see CHECKING AND CLEANING THE FILTER on this page). . Replace the filter if needed (see ORDERING REPLACEMENT PARTS on the back cover). MONTHLY . Clean the spa cover (see MAINTAINING THE SPA COVER below). . Soak the filter for two hours in a trisodium phosphate (TSP) solution. Rinse the filter in clean water. . Replace the filter if needed (see ORDERING REPLACEMENT PARTS on the back cover). EVERY THREE MONTHS . Drain the spa and refill with clean water. Sanitize and test the pH of the water. . Check for any leaks around the pump or joints in the pipes. The seals will wear out over time; detecting leaks early can reduce repair costs. . Clean the interior of the spa. Do not use solvents or waxes. EVERY SIX MONTHS . Treat the exterior with a wood sealant (see MAINTAINING THE SPA EXTERIOR below). MAINTAINING THE SPA EXTERIOR The wood panel exterior has been treated with a sealant at the factory to protect the wood from water damage. We suggest that you treat the wood finish twice a year with an additional coat of weather sealant. Contact your local spa and pool supplier for advice on which sealants work best in your climate. CLEANING THE SPA SHELL The spa shell should be cleaned with a mild soap solution. Do not use solvents. The spa should always be clean and dry before being moved or stored. MAINTAINING THE SPA COVER The spa cover should be cleaned monthly. To clean the spa cover, use water and a non-abrasive cleaner on the entire cover. Rinse the cover with a garden hose to remove any cleaner residue. Dry the cover entirely. You should also use a non-silicone based vinyl conditioner on the cover after you clean it. This will help protect the cover from sun damage. SANITIZING THE HYDROTHERAPY SPA Please refer to your local pool and spa supplier for information concerning which chemicals you should use in your area to sanitize the spa. The most common sanitizing agent is a solid bromine concentrate. The amount required varies according to several factors, such as user load, t...
Dieses Handbuch ist für folgende Modelle:Andere Home Zubehör - Daybreak 860 WLHS86090 (590.61 kb)