Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Do not modify these products and do not use this Solar Light for a purpose for which it was not intended. 13. Do not set up the Solar Light Set if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not set up the Solar Light. 14. Keep the Solar Panel free of dirt, dust and grime. Dust covering the Solar Panel will block out sunlight causing a decrease or stoppage of efficiency in recharging the batteries. WARNING: NiCad batteries must be disposed of properly. Do not incinerate. Batteries may burst, causing personal injury and/or property damage. Contact your local hazardous waste disposal authority for proper disposal. WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking the Solar Light Set, check to make sure parts on page 5 are included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353. Assembly/ Operation Your Solar Light Set will require complete assembly. The Solar Light Set requires special conditions for set up and operation. It is important that you read the entire manual to become familiar with the product BEFORE you use the Solar Light Set. Before operating the Solar Light Set be sure that you have all parts described in the Parts List and Assembly Diagram located on page 5 of this manual. 1. Decide where you want to place the Solar Light Set. Choose a location that receives full, direct sunlight a minimum of six hours a day. The location should not be near nighttime light sources such as porch lights or streetlights as this may trigger the lights to turn off or flicker. 2. The Solar Light Set will need to charge for at least 6 hours before using it for the first time. 3. Each light is powered by a battery. Each Battery (6) has a pull tab that keeps the battery disconnected until you are ready to use the Solar Light Set. To access the battery, see steps 4, 5 and 6. Refer to the section, “Replacing the Battery” and see Figure 1. 4. Remove the Solar Assembly (3) by unscrewing it from the Cover (1) and gently pulling it off. Unscrew the three screws from the Solar Assembly (3)-see Figure 1. 5. Carefully separate the top portion of the Solar Assembly (3) from the bottom piece as seen in Figure 1. Be careful to not bump or pull on any wires while doing this. If any wires are pulled, they may disconnect and disable the Solar Light. 6. Remove the pull tab from the Battery (6) so that the battery in each light is connected and providing power to the Solar Light. The pull tab can be grasped with long nosed pliers through the hole in the Solar Assembly. Note: Keep the pull tab and attach it to the battery when the Light Set is being stored and not being used. Note: During the day, the Solar Panel converts sunlight into electricity, recharging the battery. The amount of light the Solar Panel receives depends on placement of the Solar Light Set, geographic location and weather. If the weather is cloudy and the panel did not receive a full charge, the Solar Light Set may not achieve the full hours of operating time. It will catch up on its own after two to three days of full sun. 7. Slide the top Tube (4) into the Cover (1). Set another Tube (4) into the top Tube (4). Slide the Stake (6) onto the lower Tube (4)-see Fig. 2. Warning: Before inserting the Solar Lights into the ground, make certain to choose an area where there are no underground pipes, cables or other obstructions. Make certain that the ground is soft enough to accept the Stakes (6). Gently insert them into the ground making certain that it is in solid. Make certain that the Stake (6) is completely inserted into the ground to assure full stability for the Solar Light. Replacing the Battery It is recommended that you replace the battery in each Light every 12 months. 1. Remove the Cover (1). Unscrew the three screws from the Solar Assembly (3)-see Figure 1. 2. Carefully separate the top portion of the Solar Assembly from the bottom piece as seen in Figure 1. Be careful to not bump or pull on any wires while doing this. If any wires are pulled, they may disconnect and break the Solar Light. 3. Remove the old Battery (6). Make certain that the new battery is Ni-Cd (600 mAh/1.2V) rechargeable. Install the new battery into the battery compartment. Make certain that the battery is placed according to the correct polarity. Maintenance Clean regularly with a damp towel. Do not use any type of solvent for cleaning. Do not put too much pressure on the light or components while cleaning. Dry thoroughly. 07e Parts List Part # Description Quantity Part # Description Quantity 1 Cover 4 5 Stake 4 2 LED Light 4 6 Batt...