Stimmen - 2, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Attach the second Ceiling Plate the same way. Attach a Corner Bracket (26) at the top of each Corner Stud (1) so that the bracket 8. faces upwards, see diagram to the right. Leave the bottom holes of the two rear Corner Brackets (26) empty to allow the rear brace to be attached to those holes in the next step. Attach the Rear Brace (23) to the 9. inside of the two Corner Brackets (1) that are over the Rear Floor Plate (16). Attach each end to the lower hole on the Corner Bracket (26) using a Long Bolt (60) and Nut (61). (See Figure A.) Assembling the Roof Frame 28141339325415b15aFigure B 1. At the side of the Greenhouse: Assemble the Front Crown (15a) to the Rear Crown (15b) using the attached bracket. Attach the Front-Right and Front-Left Crown Beams (2, 2. 3) to the outside of the Crown Ass’y (15) with the angled edges towards the top. See diagram to the right, viewed from under the Crown, facing forward. Attach the Top Doorway Beam (14) and Door Rail (28) 3. assembly to the outside (opposite the Crown) of the Front- Right and Front-Left Crown Beams (2, 3). Attach the Front-Center Top Stud (13) to the center of the Top Doorway Beam (14).4. 5. Attach the Front-Center Top Stud (13) to the Front Crown Beams (2,3) using the Top-center Connector (39) as shown below right. Attach the Rear Crown Beams (4,5) to the Crown 6. (15b) in the same fashion as the Front Crown Beams in step 2. Attach a Corner End Cap (68) onto the outer end of 7. each Crown Beam (2-5). Cover the gaps between the Crown Beams (between 2-3 & 4-5) with a Peak Cap (72) in each. You may desire to use some silicone (not included) to secure the Peak Caps (72) in place. With two assistants, lift the Crown Assembly and place the Crown Beams (2-5) on 8. top of the Corner Brackets (26). (See Figure B.) Secure each corner in place with the Crown Beams on the outside of the Corner Brackets. Assembling the Studs and Braces The 13 spots requiring a Hold-down Connector (44) are marked with a plus (+). Figure CNote: All Side Studs (12) with no asterisk are assembled using a Long Bolt (60) for the bottom connection. All Side Studs (12) marked with an asterisk (*) are assembled with one Long Bolt (60) in the middle of the slot. 19215626312* 121212* 2222TOPTOP12* 121212* 222224246721211919891039+ + + + + + + + + + + + + 1. Attach the Rear-Left, Rear-Right, and Rear-Center Studs (8, 9, & 10) to the outside of the Rear Floor Plate (16) and Rear Brace (23). Slide a Hold-Down Connector 391323 (44) under the base and over the Bolt at each Floor Plate (16) connection. Use Long Bolts (60) for the Rear Brace (23) connections. 2. Attach the tops of the Rear Studs (8, 9, & 10) to the Rear-Right and Rear-Left Crown Beams (4, 5). For the Rear-Center Stud (10), use a Top Center Connector (39) to connect to the Crown Beams, as shown to the right. Refer to the 3. Note in Figure C. Attach the two Side Studs (12) in the center of each side (without asterisks in Figure C) to the outside of the frame. Make the bottom connections using a Long Bolt (60) for later assembly of the Side Diagonal Brace (22). Slide a Hold-Down Connector (44) under the base and over the Long Bolt at each bottom connection, but do not install a Nut (61) over the Long Bolt yet. Refer to the 4. Note in Figure C. Attach the two Side Studs (12) near the corner of each side (with asterisks (*) in Figure C) to the outside of the frame. Slide a Long Bolt (60) into each slot for later Side Diagonal Brace (22) assembly. Slide a Hold- Down Connector (44) under the base and over the Bolt before installing the Nut (61) at each bottom connection. Attach a Side Diagonal Brace (22) to the lower hole of a Corner Stud (1) on the 5. inside with the TOP arrow pointing towards the Corner Stud as shown in Figure C. Use a Long Bolt (60) to attach the Brace. Attach the other three Side Diagonal Braces (22) to the other Corner Studs (1) in the same manner. Attach the center hole of each Brace to the Long Bolt (60) in the center of the Side 6. Studs (12) designated with an asterisk (*) in Figure C. This Bolt (60) was included in step 4, above. Attach the bottoms of all four Side Diagonal Braces (22) to the Long Bolts (60) 7. installed at the bottoms of the remaining Side Studs. View from abovetoCorner Stud (1) Left Doorway Stud (6) Front Floor Plate (17) toCorner Stud (1) Right Doorway Stud (7) 8. Install the Left and Right Doorway Studs (6 & 7) to the outside of the frame so that they rest flat against the frame. Their orientation should be the same as shown above. Slide a Long Bolt (60) into each slot for later Front Brace (21) assembly. Make the bottom connections using a Long Bolt (60) for later assembly of the Front Diagonal Braces (24). Slide a Hold-Down Connector (44) under the base and over 391045 the Long Bolt at each bottom connection, but do not install a Nut (61) over the Long Bolt yet. Remove the bottom Bolt from the Corner Brackets (26) at the front of the green9. house. Install the Front Diagonal Braces (24) to t...