Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Assembly Instructions Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. WARNING! Make sure the Power Switch of the Timer is in its “OFF” position and that the Pet Water Fountain is unplugged from its electrical outlet before making any adjustments to the unit. Insert the Pump (11) into the Base (1). Fit the Clear Tube (12) into the holding slot in the Base. Then, place the Pump’s Power Cord in the wire holders along the side of the Base. (See Figure A.) FIGURE AFIGURE BPUMP (11) PUMP POWER CORDCLEAR TUBE (12) CLEAR TUBE (12) Make sure all Tubes are properly connected. Remove any sharp bends or kinks in the Clear Tube (12) or water flow could be reduced. (See Figure B.) FILTER (3) FIGURE CAlign the Filter (3) into the corner slots of the Base (1) and press the Filter down into the water chamber. Use the correct slot, and do not use excessive force. (See Figure C.) Feed the Power Cord of the Pump (11) through the square hole in the back of the Water Tank Stand (16). Make sure the Power Cord is secured by the wire holders on the side of the Base (1). (See Figure D, next page.) WATER TANK STAND (16)BASE (1) FIGURE EWATER TANK STAND (16)FIGURE DCarefully slide the Water Tank Stand (16) into the Base (1) while pulling the Power Cord of the Pump (11) out the back of the Water Tank Stand. Make sure all of the Power Cord comes out the back. (See Figure E.) FIGURE FWATER TANK WATER TANK CAP (6) WATER TANK GASKET (5) FIGURE GWATER OUTLET (8) Fill the Water Tank (4) with clean, cool water. Make sure the Water Tank Gasket (5) is properly seated in the Water Tank Cap (6). Then, screw the Water Tank Cap onto the Water Tank. (See Figure F.) Turn the Water Tank (4) upside down. With the black Water Outlet (8) on the Water Tank pointing to the hole in the Water Tank Stand (16), insert the Water Tank into the Water Tank Stand. (See Figure G.) MUSHROOM HEAD (2) MUSHROOM STAND (17) AC/DC ADAPTER (9) TIMER UNIT (10)FIGURE HFIGURE IInsert the Mushroom Head (2) onto the Mushroom Stand (17). (See Figure H.) Connect the AC/DC Adapter (9) to the Timer Unit (10). Then connect the Timer Unit to the Power Cord of the Water Pump (11). NOTE: Should you not want to use the Timer Unit, you can remove it and connect the AC/DC Adapter directly to the Power Cord of the Water Pump. (See Figure I.) OPERATING INSTRUCTIONS Plug the AC/DC Adapter (9) into the nearest 120 volt, grounded electrical outlet. The Water Pump (11) should start and water will come out from the nozzle or from the Mushroom Head (2). (See Figures H and I.) Check the position of the Switch on the Timer Unit (10). Slide the Switch to 30 Min. to turn the Water Pump (11) ON for 30 minutes and OFF for 30 minutes repeatedly. Or slide the Switch to 60 Min. to turn the Water Pump ON for 60 minutes and OFF for 60 minutes repeatedly. (See Figure I.) NOTE: Slide the Switch on the Timer Unit (10) to the OFF position to turn off the Water Pump (11). It is recommended to unplug the AC/DC Adapter (9) if the Pet Water Fountain will not be used for long periods of time. (See Figure I.) Water flow speed can be adjusted by sliding the small window located on the Water Pump’s (11) side next to where the water flows out. SPRAY NOZZLE (14) FOUNTAIN NOZZLE (15) FIGURE JIMPORTANT: Dogs and larger pets will probably prefer that you remove the Mushroom Head (2) and Mushroom Stand (17) and replace them with the included Spray Nozzle (14) or Fountain Nozzle (14-1). (See Figures H and J.) 6. To install the Spray Nozzle (14) or Fountain Nozzle (14-1): a. R.m.v......M........H.....2......M................7..Remove the Mushroom Head (2) and Mushroom Stand (17). (See Figure H.) b. ..........................................................................................................................Separate the Clear Tube (12) by unplugging the 90 degree fitting that plugs into the bottom of the Mushroom Stand (17). (See Figures A, B, and H.) c. ..............w..C.............2.............................m.v............Separate the two Clear Tubes (12) at the black union. Then remove the black union and the short length of the Clear Tube (12) (See Figures A and B.) d. .......................................m....................................To use the Spray Nozzle (14), slip the male end of it (14) into the longest length of Clear Tube (12) that connects to the Water Pump (11). To use it with the Fountain function (14-1), remove the spray cover (14-2). (See Figures A, B and J.) e. .......................................................................................................................Turn on the Water Pump (11) and adjust the water flow by raising or lowering the Black Lever (13), which the Clear Tube passes through. (See Assembly diagram.) INSPECTION, MAINTENANCE, AND CLEANING WARNING! Make sure the Power Switch of the AC/DC Adapter (9) is in its “OFF” position and that the Pet Water Fountain is u...