Stimmen - 5, Durchschnittliche Bewertung: 2.8
(
)
)
|
Anleitung Zusammenfassung
6,286,249 AU Patent No. 726575, NZ Patent No. 335035 ® MADE IN USA PART NO. 1440-501 Rev. A Your trap will begin capturing immediately, but allow 4-6 weeks to interrupt the breeding cycle. 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 American Biophysics Corporation 2240 South County Trail East Greenwich, RI 02818-1536 Place First-Class Postage Here PLEASE FOLD AND SEAL WITH TAPE ALONG OPEN END. DO NOT USE STAPLES NOTICE: PLEASE READ THE ENTIRE MANUAL BEFORE ASSEMBLING AND STARTING UP YOUR MOSQUITO MAGNET DEFENDER. NOTICE: PLEASE READ THE ENTIRE MANUAL BEFORE ASSEMBLING AND STARTING UP YOUR MOSQUITO MAGNET DEFENDER. TABLE OF CONTENTS 1. Safety…………………………..……...........................................2-4 2. Parts included……………………...........................................……5 4. Additional Components ……………….............................................6 5. Assembly instructions………………............................................7-9 6. Trap Placement………………………...........................................10 7. Start-Up Instructions……………….........................................…..10 8. Shut-Down Instructions………………...........................................11 9. Tank Changing Tips..............................................................................11 9. Maintenance.........................................................................................11 10. For Best Results...................................................................................12 11. Gas Reset Tool......................................................................................12 12. Quick-Clear Valve…………………..........................................…...13 13. Burying The Cord.................................................................................13 14. Troubleshooting…………………….....................................…......14 15. Warranty……………….....................................................................15 HOW THE MOSQUITO MAGNET WORKS Humans exhale carbon dioxide (CO2), which has been scientifically proven to be the natural compound that mosquitoes and other biting insects use to navigate to people. The Mosquito Magnet mimics a person’s breath by catalytically converting propane to carbon dioxide (CO2). The Mosquito Magnet can be placed near the mosquito’s resting and breeding spots, trapping the mosquitoes at their source (see trap placement section). The female, egg-laying, biting mosquitoes are drawn away from you and to the Mosquito Magnet, where they are vacuumed into a net and dehydrate. Within 4-6 weeks, the reproductive cycles of your biting insect population are interrupted. NO EGGS. NO INSECTS. The Mosquito Magnet targets only biting insects, not beneficial insects such as butterflies, bees and moths. Congratulations on your Mosquito Magnet purchase! Please read your owner’s manual completely before assembling and operating your unit. 1 MOSQUITO MAGNET Defender SAFETY INSTRUCTIONS FOR YOUR SAFETY If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, immediately call your gas supplier. FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors and liquids in the vacinity of this or any other appliance. WARNING: For Outdoor Use Only Model No.: DEFENDER Serial No.: Type of Gas: Propane Manifold Pressure: 100-110 psi Minimum Gas Supply Pressure: 11.0 in. WC Input Rating: 650Btu/Hr. Minimum Clearances: 20-24” For Outdoor Use Only. If Stored Indoors, Detach and Leave Propane Cylinder Outdoors. 2 WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment. CAUTION: The gas pressure regulator provided with this appliance must be used. This regulator is set for an outlet pressure of 11.0 in. Water Column. The gas supply must be turned off at the LP-Gas supply cylinder when this appliance is not in use. The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1-1998 for US and with the CAN1-B149 for Canada. Adequate clearances of 20-24 inches around air openings into the combustion chamber, clearances from combustible material, provisions for accessibility and for combustion and ventilating air supply. The minimum inlet gas supply pressure is 11”WC from regulator. To test for a gas leak, place soapy water around the regulator. If bubbles appear, there is a gas leak. Route the power cord in the safest possible manner to avoid personal injury. The hose assembly must be replaced prior to the appliance being put into operation if there is evidence of excessive abrasion or wear, or if the hose is damaged. The instructions shall state that the replacement hose assembly shall be that specified by the manufacturer. The...