Login:
Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Anleitung PAC, modell C2R-CHY4

Hersteller: PAC
Dateigröße: 297.22 kb
Dateiname: c2r-chy4_instructions_060809.pdf
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


Output (1 amp) Red / White P.B. Output (-) Purple / White VSS Output (Pulse) Orange / White Illum. Output (+) Green Reverse Output (+) White / Green SWC Output Blue / White Amp Turn On Input C Radio Specific Steering Wheel Control Interface (Sold Separately) Program SWC Interface for Version 2. Installation Notes: 1. Only one of the two provided radio harnesses will be used. Remove the factory installed radio to determine the correct harness for your particular vehicle. 2. Vehicles without a factory amplifier: Connect the aftermarket radio's front and rear speaker wires to the 22 pin plug. 3. Vehicles with a factory amplifier: The factory amplifier only accepts two audio channels (left and right). The amplifier's fading is controlled by data communication from the factory radio. The aftermarket radio does not have the ability to control the amplifier's fader. Connect the front outputs of the aftermarket radio to the rear inputs of the 22 pin radio connector. This will allow navigation voice prompts and Bluetooth calls to be heard. The rear speaker outputs of the aftermarket radio are not used. 4. Vehicles with a manual transmission will not support a reverse trigger output. 5.The accessory output wire is located on the 11 pin CAN INTERFACE harness - connect this wire to the radio's accessory wire. The accessory wire supplies +12v, 1 amp max when key is in the accessory or ignition position (fig. 1: If more current is needed). 6. 11 pin plug (to CAN INTERFACE): 1. 2. 3. 4. 5. 6. High Current 12v (Fused) Blue/White - Connect this wire to the radio's amplifier remote output. Connect this wire with or without OEM amp present! White/Green - SWC output. Green - Connect this wire to the radio's reverse input wire only. Orange/White - Connect this wire to the radio's Illumination input wire only. Violet/White - Connect this wire to the radio's VSS input wire only. Red/White - Connect this wire to the radio's parking brake input wire only. Note: Do not connect these wires to any circuit other than the radio's wire harness. 7. 11 pin plug (to SWC INTERFACE): This is a quick connection to a radio specific SWC interface. No additional connections are necessary other than radio control connections. Plug the radio specific SWC interface in to this connector and program the radio specific SWC interface for version 2. Do not cut the loops. Refer to the SWC interface instruction manual for the radio specific control function programming order. 8. Refer to the aftermarket radio's instruction manual for testing VSS, Reverse, Parking Brake and Illumination outputs. For the most current and Up-to-Date application guide please visit Fig. 1 (using a SPDT relay) 12v Acc. From — Interface Diode 1N4005 or equivelant • 85 87 86 LüJ Ground New High Current Output DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the C2R-CHY4 be held liable for consequential damages sustained in connection with the C2R-CHY4. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the C2R-CHY4 other than its replacement. 10 13 08 Pacific Accessory Corporation - Santa Ana, CA 92705 techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com...


Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien