Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Works with or without factory satellite receiver installed. Pacific Accessory Corporation Installation: The AAI-NIS2 plugs into the back of the factory radio. If the factory SAT radio tuner is present and not currently serviced, the AAI-NIS2 interface must be used in the “No SAT” mode. The original 12 pin SAT connector should NOT be connected to the AAI-NIS2 interface. It is highly recommended that you disconnect the negative battery cable prior to installing the AAI-NIS2. Do not turn on the vehicle while the SRS wire harness plug is removed from the dash bezel. Doing so may cause the SRS air bag light to turn on and may need to be reset by the dealer. 1. Remove the factory radio. Remove the factory female 12 pin Satellite cable, if available. Plug the AAI-NIS2’s 12 pin SAT plug into the radio. Plug the factory Satellite cable that was just removed into the AAI-NIS2’s 12 pin connector ONLY if the SAT tuner is serviced . 2. Insert the AAI-NIS2’s 10 pin main power Plug (T-Harness) in between the factory radio and factory harness. For vehicles without the 10 pin main power plug, connect the AAI-NIS2’s 10 pin red wire to the vehicle’s accessory +12v circuit. 3. Connect external audio device (s) into Aux 1 and/or Aux 2 inputs using the RCA jacks on the AAI-NIS2. Blue/Black wire: Aux 1 (-) remote output. This wire provides a negative output when radio is in Aux 1. (300 ma. max output, use relay when necessary) Yellow/Black wire: SWC output. This wire will send data signals to PAC’s SWI-X (optional) when using the steering wheel audio controls or radio controls. For vehicles without PRESET ABC buttons. This output only works when in [No SAT] mode. 12 pin SAT plug 10 pin main plug Yellow/Black - Connect to SWI-X’s (optional) Yellow wire. Blue/Black - Aux1 (-) remote output. 300ma. maximum output. AAI-NIS2Nissan/Infiniti Auxiliary Audio InputPacific Accessory Corporation • Santa Ana, CA 92705 Aux 2InputLeft Right Aux 1Input With SAT / No SAT Vehicles Without Factory Satellite. Slide Switch on side of AAI-NIS2 to [ No SAT ] position. Operation: Radios that have SAT or RADIO button. 1. Turn the factory radio on. Press the SAT or RADIO button to select the Aux inputs. SR1 [Aux 1] or SR2 [Aux 2] will show on the display. The Aux1 remote wire will turn on only if you are in SR1. 2. Pressing the Mode button on the steering wheel will scroll through CD, Tape AM, FM1, FM2, SR1 and SR2. 3. Pressing CD, Tape, FM/AM or Radio will exit out of Aux mode, turning off the remote wire. Operation: Radios with PRESET ABC button. 1. Turn the factory radio on. To select Auxiliary 1, press the PRESET ABC until ‘A’ is displayed - press the SAT button to select [Aux 1] input. To select Auxiliary 2, press PRESET ABC until ‘B’ is displayed. - press the SAT button to select [Aux 2] input. PRESET C is not used. 2. Pressing the Mode button on the steering wheel will scroll through PRESET A, B and C when in Auxiliary mode. The other controls on the steering wheel and radio control the factory radio differently than the G35, 350Z and Pathfinder. Therefore the SWC output is not usable with the SWI-X. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the AAI-NIS2 be held liable for consequential damages sustained in connection with the AAI-NIS2. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the AAI-NIS2 other than its replacement. Pacific Accessory Corporation - 1502 S. Santa Fe Street, Santa Ana, CA 92705 techsupport@pac-audio.com • Vehicles With Factory Satellite. Slide Switch on side of AAI-NIS2 to [ With SAT ] position. Note: The Steering wheel output is not active during this mode. If the SAT tuner is not serviced it must be disconnected and the No SAT mode must be used. Operation: G35 with SAT button. 1. Turn the factory radio on. Press and release the SAT button until SR2 is selected (in some cases, SR1 may have to be selected). Press Preset 1 to enter [Aux 1] or Preset 2 to select [Aux 2]. Preset 3 to 6 will select normal satellite presets. 2. Pressing the Mode button on the steering wheel will scroll through CD, Tape AM, FM1, FM2, SR1 and SR2. 3. Pressing CD, Tape, FM/AM will exit out of Aux mode, turning off the remote wire. Operation: G35, 350Z and Pathfinder with Radio button. 1. Turn the factory radio on. Press and release the Radio button until SR2 is selected. Press Preset 1 to enter [Aux 1] or Preset 2 to select [Aux 2]. Preset 3 to 6 will select normal satellite presets. 2. Pressing the Mode button on the steering wheel will scroll through CD, AM, FM1, FM2, SR1 and SR2. 3. Pressing CD, Tape, FM/AM or Radio will exit out of Aux mode, turning off the remote wire. Operation: Radios with PRESET ABC button and SAT Button. 1. Turn the factory radio on. Initializing buttons: Press PRESET ABC button until ‘B’ is displayed. Press the SAT button. Press and hold preset #1 until ...