Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Plug into a grounded 3 prong outlet. 6. Determine whether you want the compactor cabinet or drawer front flush with the kitchen cabinet face. Using 2 - #8 - 18 x ..." mounting screws (provided), attach the retaining brackets to the compactor cabinet top as needed. ¦ If the compactor cabinet face is to be flush with the kitchen cabinet face, place retaining bracket mounting screws through “1.” ¦ If the compactor drawer front is to be flush with the kitchen cabinet face, place retaining bracket mounting screws through “3.” ¦ If the compactor is to be midway between “1” and “3,” place the retaining bracket mounting screws through “2.” Position 3: 34...." to 34..." (87.5 to 88 cm) NOTE: To level the unit in position 3, you may need to add shims under the front leveling legs. ¦ Tighten screw. Repeat for other rear wheel. B 1 2 3 C D A B A 123 A. Countertop B. Retaining bracket 7. Slowly lift the front slightly and roll compactor into the kitchen cabinet opening. 8. Using 2 - #8 -18 x .." mounting screws (provided), fasten the retaining brackets to the countertop with the mounting 2. Use pliers to lower front leveling legs away from compactor cabinet. Adjust legs so there will be a ..." (3 mm) to .." (6.4 mm) space between the top of the compactor and the top of the kitchen cabinet opening. Stand the compactor upright. 3. Move the compactor close to its final position. 4. To install handle: Insert screws into the holes from the inside of the drawer. Place handle on the front of the drawer and align handle screw holes with screw ends. (The handle should appear as a “smile” when installed.) Tighten screws snugly. screws. Countertop mounting NOTE: If retaining brackets cannot be attached to the underside of countertop, attach mounting clips (provided) to retaining brackets. Fasten compactor to kitchen cabinet face A. Wheel bracket assembly B. Compactor cabinet C. Locating stud D. Self-tapping screw (pivot) A C B A B C A. Countertop B. Retaining bracket C. Mounting screw (provided) with mounting screws through the mounting clips. A. 2 screws inserted into holes from inside of drawer B. Top of drawer C. Handle installed on drawer front 8 Cabinet-face mounting 9. Grasp sides of compactor drawer and place bottom of drawer into tracks. Lift at the handle so drawer will go over drawer stops. Close drawer. Check to see whether drawer opens freely. If the toe plate rubs against floor, see “Adjusting the Toe Plate” for further instructions. Adjusting the Toe Plate If the toe plate rubs the floor covering, the toe plate clearance may be changed as follows: 1. Mark on each side of the toe plate the amount of toe plate that rubs the floor covering. 2. Remove the drawer from the unit. See Step 3 in the “Unpacking” section. 3. Use a ruler and a pencil or chalk to draw a line between the marks on each side of toe plate. 4. Use scissors or utility knife to cut toe plate along line. 5. Replace drawer. If toe plate still rubs floor covering, repeat steps 1-4. COMPACTOR USE How Your Compactor Works The compacting ram is the part of the compactor which compresses the trash. The compacting ram does not go to the bottom of the drawer. You will not see compacting of trash the first few times you load the compactor. NOTE: The compactor drawer should be more than ... full before the compactor can begin to compress the load. You may hear a noise when glass breaks. Strong glass bottles may not break at all. The trash in a full compactor bag will be about ... the size of its original bulk. Load bulky trash, bottles, and cans in the center of the drawer. Bottles or cans not placed in the center may become caught between the ram and the drawer. The Drawer Monitor Switch then senses a “misload” and causes the ram to return to the “up” position without compacting. Loading IMPORTANT: Do not push items down into compactor with hands or feet. 1. Lift and pull the handle or press the foot pedal to open the compactor drawer. NOTE: Pressing the foot pedal opens the container only 3" to 6" (7.6 cm to 15.2 cm), depending on the load. Use the handle to completely pull out the compactor drawer. 2. Place trash in compactor. Wrap or cover wet or messy trash. Do not compact items that may develop offensive odors such as raw meat, fish, grapefruit rinds, disposable diapers, or personal hygiene items. Load bottles or cans on their sides in the center of the drawer. Do not load bottles in an upright position. 3. Close the drawer. A. Mounting clip (provided) B. Kitchen cabinet C. Retaining bracket D.Mounting screw (provided) A D C B Starting Your Compactor 1. Lift and pull the handle or press the foot pedal to open the compactor drawer. Load trash. 2. Keep Key-Knob (located on the control panel) in the “ON” position. A A. Control panel 3. Set Cycle switch to Normal Pac. 4. Close compactor. 5. Lift foot pedal up to start the compacting cycle. NOTE: When the compacting cycle is completed, open the drawer and turn the Key-Knob to “OFF.” Remove the Key-Knob and ...