Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Haier Dateigröße: 1.56 mb Dateiname: hpimd25_manual.pdf Unterrichtssprache:

4. Each cycle produces 9 cubes of ice. The ice making cycle takes about 6 to 15 minutes, depending on the ambient (room) temperature. Ambient and initial water temperatures affect the actual ice making time. It is not suggested to try making ice if room temperature exceeds 90. degrees farenheit as ice making time may vary greatly. 5. The default size of the ice cube is medium. If you want small size cubes, press the “Select” button on the control panel and the LED indicator should switch from “M” to “S”. If room temperature is lower than 60. degrees Fahrenheit, it is recommended to select small size cubes. Maximum Water Level Fill the water here Funnel 7 6. During the operation process, if the level of the water in the reservoir becomes to low, the “Add Water” LED indicator will display. NOTE: If for any reason such as water shortage, to much ice, power off, etc., do NOT restart the machine right away. Wait at least 3 minutes before attempting to restart. 7. The ice maker automatically stops producing ice when the ice storage compartment is full. The “Ice Full” LED indicator will light as confirmation. NOTE: As a safety precaution, the auger inside the ice storage compartment and dispensing will automatically stop working if the transparent hatch on top of the unit is even partially open. WARNING: Do NOT attempt in any way to disable the safety switch activator on the transparent hatch or inside the ice storage compartment. 8. To dispense the ice, push forward on the ice cube dispenser paddle. That will activate the auger inside the ice storage compartment, first back, then forward and allow ice cubes to drop down the shoot. The blue overhead light should also come on when paddle is pushed forward. NOTE: Transparent hatch on top of the unit must be closed fully for auger to operate and ice to dispense. WARNING: • Never clean the ice maker unless the power is OFF and unit is unplugged. • Full strength solvents, detergents, and abrasives must never be used for cleaning. • Never tilt or place the icemaker on its side, otherwise you must wait 2 hours for compressor coolant to settle. It is recommended that the appliance is cleaned once a month or more frequently in areas where chalky deposits can be a problem. A recommended cleaning solution is 1 part vinegar to 10 parts water. The appliance should be allowed to complete one ice making cycle, thoroughly rinsed with fresh water and dried with a soft cloth. Any residual vinegar may cause the next ice cubes to be soft or slushy. If this happens, the unit should be rinsed again with fresh water. Before using your ice maker, it is strongly recommended to clean it thoroughly 1. Power should be off and unit unplugged 2. Clean the interior with diluted vinegar solution, warm water and a soft cloth 3. Use water to rinse the interior and remove water thru the drain by removing the drain cap. 4. It is suggested to change the water in the reservoir daily for optimum hygiene. English cleaning and maintenance 8 5. If the unit isn’t used for an extended period of time, remove all water left in the reservoir and ice storage compartment thru the drain. 6. Clean the outside of the ice maker regularly with a mild detergent solution and warm water. 7. Dry the interior and exterior with a soft cloth. How to drain all the water from both the water reservoir and ice storage compartment 1. Power should be off and unit unplugged. 2. Place the icemaker in a position where water can be collected from the drain. 3. Remove water drip tray/cup-glass holder to access drain. (see image below) 4. Remove drain plug and let water flow out. (see image below) 5. Replace drain plug and clean the water reservoir and ice storage compartment with diluted vinegar solution. 6. Use water to rinse the water reservoir and ice storage compartment. 7. Remove drain plug and let water flow out. 8. Replace drain plug and dry water reservoir and ice storage compartment with soft cloth. 9. Store ice maker in dry, clean area. NOTE: When moving the unit, it is better to allow the refrigerant liquid inside the compressor to settle at least 3 minutes before restarting. English Remove the Water drip tray Unplug the drain cap 9 English TRoubleshooting guide Problem Possible Causes Solution Power LED indicator will not come on Plug disconnected from wall outlet Check that unit is plugged into standard 120V, 60 Hz outlet. Also make sure outlet has power and circuit breaker is not tripped. “Ice Full” LED indicator is on Storage compartment is full Remove ice from storage compartment via the dispenser Ice cubes in storage compartment but do not come out the dispenser Transparent hatch is open Close hatch securely, resetting safety switch and reactivating auger Auger in ice storage compartment is blocked Release ice dispenser paddle, wait 10 seconds, push ice dispenser paddle forward again “Add Water” LED indicator is on Water reservoir is empty or water level is low Use provided funnel to add water to reservoir on side of ...

Herunterladen

Geben Sie zwei Ziffern: